background image

EN - 4

Read these safety rules and follow them 
closely. Failure to follow these rules could 
lead to loss of control of unit, severe personal 
injury or death to you or bystanders or result 
in damage to property or the machine.

Safety Alert Symbol

SIGNAL WORDS

The safety alert symbols above and signal 
words below are used on decals and in this 
manual.

Read and understand all safety messages.

1. Danger

2. Warning

3. Caution

4. Notice

NOTICE:

 Indicates information or procedures 

that are considered important but not hazard 
related. If not avoided property damage could 
result.

5. Important

IMPORTANT: 

Indicates general reference 

information worthy of special attention.

SAFETY DECALS

This splitting machine is capable of crushing 
or amputating body parts. Failure to observe 
the following safety instructions could result 
in serious injury or death.
The safety decals on your machine are visual 
reminders of the important safety information 
found in this manual. All messages found on 
your unit must be fully understood and 
carefully followed. Safety decals found on the 
machine are explained below.

Always replace missing or damaged safety 
decals. Replacement decals can be found in 
the parts manual for your machine and 
ordered from your dealer. 

Refer to Figure 2 for Safety Decal locations.

SAFETY

WARNING: 

This splitting machine 

is capable of crushing or 
amputating body parts. Failure to 
observe the safety instructions in 
the manuals and on decals could 
result in serious injury or death.
Tragic accidents can occur if the 
operator is not alert to the 
presence of children. Never 
assume that children will remain 
where you last saw them.

Gasoline is extremely flammable 
and the vapors are explosive, 
handle with care.

Stop engine and allow moving 
parts to stop before leaving 
operator’s position.

These are safety alert 
symbols. They mean: 

ATTENTION! 

YOUR SAFETY IS 
INVOLVED! 

 When you see this symbol:

BECOME ALERT! 

OBEY THE 
MESSAGE!

DANGER: 

Indicates an 

IMMINENTLY HAZARDOUS 
SITUATION! If not avoided, WILL 
RESULT in death or serious injury.

WARNING: 

Indicates a 

POTENTIALLY HAZARDOUS 
SITUATION! If not avoided, COULD 
RESULT in death or serious injury.

CAUTION: 

Indicates a 

POTENTIALLY HAZARDOUS 
SITUATION! If not avoided, MAY 
RESULT in minor or moderate injury. 
It may also be used to alert against 
unsafe practices.

Summary of Contents for 22-Ton Log Splitter



























Reviews: