background image

GB - 5

DELIVERY

Customer Note: If you have purchased this product 
without complete assembly and instruction by your 
retailer, it is your responsibility to:

1. Read and understand all assembly instructions in 

this manual. If you do not understand or have 
difficulty following the instructions, contact your 
nearest Ariens Dealer for assistance. Make sure 
all assembly has been properly completed.

NOTE: To locate your nearest Ariens Dealer, call 
1-920-756-4664 or go to www.ariens.com on the 
internet.

2. Understand all Safety Precautions provided in the 

manuals.

3. Review control functions and operation of the 

unit. Do not operate the Sno-Thro unless all 
controls function as described in this manual. 

4. Review recommended lubrication, maintenance 

and adjustments.

5. Review Limited Warranty Policy. 

6. Fill out a Product Registration Card and return the 

card to the Ariens Company or go to 
www.ariens.com.

SAFETY ALERTS

Look for these symbols to point out 
important safety precautions. They mean:

Attention!   

Personal Safety Is Involved!

Become Alert! 

Obey The Message!

The safety alert symbols above and signal words below 
are used on decals and in this manual. Read and 
understand all safety messages.

 

NOTATIONS

NOTE: General reference information for proper 
operation and maintenance practices.

IMPORTANT: Specific procedures or information 
required to prevent damage to unit or attachment.

PRACTICES AND LAWS
Practice usual and customary safe working 
precautions, for the benefit of yourself and others. 
Understand and follow all safety messages. Be alert to 
unsafe conditions and the possibility of minor, 
moderate, or serious injury or death. Learn applicable 
rules and laws in your area. Always follow the practices 
set forth in this manual.

REQUIRED OPERATOR TRAINING
Original purchaser of this unit was instructed by the 
seller on safe and proper operation. If unit is to be used 
by someone other than original purchaser; loaned, 
rented or sold, ALWAYS provide this manual and any 
needed safety training before operation.

WARNING: Improper assembly or 
adjustments can cause serious injury.

SAFETY

WARNING: To avoid injury to hands and feet, 
always disengage clutches, shut off engine, 
and wait for all movement to stop before 
unclogging or working on snow thrower.

Hand contact with the rotating impeller is the 
most common cause of injury associated with 
snow throwers. Never use your hand to clean 
out the discharge chute.

Keep hands and feet away from auger and 
impeller.

DANGER: IMMINENTLY HAZARDOUS 
SITUATION! If not avoided, WILL RESULT in 
death or serious injury.

WARNING: POTENTIALLY HAZARDOUS 
SITUATION! If not avoided, COULD RESULT 
in death or serious injury.

CAUTION: POTENTIALLY HAZARDOUS 
SITUATION! If not avoided, MAY RESULT in 
minor or moderate injury. It may also be used 
to alert against unsafe practices.

Summary of Contents for 624E































Reviews: