background image

AN1808-12S

 

4G

 Audio Intercom (E2.2) 

 11/16 

Programming by text message 

Programming by text message is the simplest way to customize the settings of the intercom and add 

or delete telephone numbers. Simply send texts in the format to the telephone number of the SIM 

within the intercom. 

Note:   

1.

A Single SMS text messages is limited to 140 characters.

2.

You can program many different user command codes in one text message with SMS

command format. 

*12*1234 # [command Code1] # [command Code 2] # [command Code3] #...

3.

Each SMS must start with the pass code, default 1234 in the following format 

*12*1234 #

followed immediately by a command.

4.

To program call button numbers DO NOT enter country code, just the complete number as you

would dial it.

Example: 

Store a call button phone number (Max 3 numbers) and delete 2&3 phone numbers. 

058 57235      (landline number 1) 

086 5682554 (mobile number 2) 

086 2235644 (mobile number 3) 

SMS format: (store a call button phone numbers) 

*12*1234#

1

1

05857235#

1

2

0865682554#

1

3

0862235644#

SMS format: (delete 2&3 phone numbers from a call button) 

*12*1234#

12*#13*#

User command code CORRECT 

SMS format: 

*12*1234#

1

1

05857235#

1

2

0865682554#

1

3

0862235644#

SMS reply:

1

1

05857235#

1

2

0865682554#

1

3

0862235644# OK

User command code ERROR (user command 

1

9

 error) 

SMS format: *12*1234#1105857235#

1

9

0865682554#130862235644# 

SMS reply: 110587235#190865682554# Error 

Command to use: *12*1234#

1[Y][phone number]# 

       

Y= number 1, 2 or 3

 

Summary of Contents for AN1808-12S

















Reviews: