Aristo 320 Instruction Manual Download | Manualshive

Page: 7 / 12

background image

-- 47 --

bu09d12e2

The power supply should be lifted by means of its lifting

eye. The handle is only intended for pulling it along the

ground.

Lifting instructions

IMPORTANT

S

Place the welding power source in a suitable place and make sure the welding

rectifier is not covered or set--up so that cooling is prevented.

S

Make sure the welding rectifier is connected to the correct mains voltage.

Earth according to applicable directives.

GB

«
...
5
6
7
8
9
...
»

Summary of Contents for 320













Reviews:

No comments

Related manuals for 320

security system

Brand: Safe-at-home Pages: 5

Brand: FBII Pages: 48

Brand: Panasonic Pages: 2

Brand: Barnstead|Thermolyne Pages: 56

Brand: Abus Pages: 4

Brand: Castex Pages: 23

Brand: R-Tech Pages: 19

Brand: Ravaglioli Pages: 72

Brand: JBL Pages: 2

Brand: WELDY Pages: 44

Brand: Marco Pages: 3

TRANSTIG 200 AC/DC

Brand: CIGWELD Pages: 128

Brand: Kühtreiber Pages: 44

ABIPLAS WELD 100 POWDER W

Brand: BINZEL-ABICOR Pages: 96

Brand: salmson Pages: 20

Brand: Miller Pages: 32

Brand: Cary Audio Design Pages: 41

Brand: Spartus Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands