P/N 466-5611-
ML • REV A • ISS 30JUL21
3 / 16
See Figures 5 and 6 for ACL870FL-PB and ACL870SU-PB
wiring.
To:
From
ACL870FL-
PB
ACL870SU-PB Door
Magnet /
Door
Strike
ACL585
RS485
–
A (pink)
RS485
– A
RS485
– A
(pink)
ACL585
RS485
–
B (violet)
RS485
– B
RS485
– B
(violet)
ACL585
POWER
GND
GND
GND (black)
ACL585
POWER
+12V
+12V
+12V out
(brown)
Ext. PSU
GND
GND
GND (black)
Ext. PSU
+12V
+12V
+12V (red)
Ext. PSU
GND
NO1 &
COM2
COM (yellow)
Ext. PSU
+12 V
+12V
Door Strike
COM1
NO (white)
Door Magnet
NC2
GND
LEDs
See Figure 3.
There are three LEDs on the keypad:
•
Red (item 1): Relay 2 status (on the ACL870FL-PB)
•
Green (item 2): Relay 1 status
•
Orange (item 3): Key press and menu
DIP switches
See Figure 7.
•
1: Reset master code. See “Reset master code” below for
details.
•
2: TERM: Set to On for the built-
in RS485 120 Ω bus
termination.
Installation
Mounting
Figure 1
(A) Flat surface
(B) Magnet holder
To install the keypad, follow the steps in the figure.
Wiring
See “Keypad wiring” on page 2.
Pairing keypad with ACL870FL-PB or ACL870SU-PB
1. Close the jumper (ACL870FL-PB) or set DIP switch to On
(ACL870SU-PB). The unit beeps continuously, and the red
LED blinks.
2. Open the Jumper / DIP switch
3. Wait for beep and OK beep (short, short, long beep). After
the OK beep, the keypad and ACL870FL-PB / ACL870SU-
PB are paired.
Configuration
Reset master code
Caution:
Resetting the master code will delete all user codes.
Resetting the master code will also unpair ACL870FL-PB and
ACL870SU-PB.
See figure 5.
1. Disconnect power and set DIP switch 1 to On (Figure 7,
item 1).
2. Reconnect power.
The keypad beeps continuously.
3. Set DIP switch 1 to off.
Orange LED switches on, long beep sounds.
4. Press 000.
5. Enter the new master code (1 to 8 digits).
6. Press A to confirm.
7. Press B to exit.
Orange LED switches off.
Programming mode
To change keypad options, follow the steps below.
1. Authorize using the master code, or 000 when using the
keypad for the first time.
2. Validate the code by pressing B.
If you are not authorized to enter the programing mode,
the keypad transmits multiple short beeps, and the orange
LED blinks rapidly.
If the code is valid, the programming mode is signalled by
1 short and 1 long beeps, and indicated by the orange
LED on. You can continue with the programming.
3. Enter the option number you want to change. Refer to
4. Press A to validate the change.
If the change is invalid, the keypad transmits multiple short
beeps, and the orange LED blinks rapidly. Return to
step 3.
If the change is valid, it is confirmed by 2 short beeps.
Return to step 3.
To exit the programming mode, press B in any stage of the
programming mode. The orange LED switches off.
Programming options
When in the programming mode, press a number to program
one of the following options.
