background image

ARITERM SWEDEN AB 

 ARITERM OY

 

• Asennus ja käyttöohje • Installation och driftanvisning • Installation and operating instruction • UK 25.05.2012 • 

19/32

ARITERM-VTT-S-07229-11.1

Alarm message / Cause

Check that

Procedure

Alarm control level monitor

The level switches have not detected 

pellets in the burner upper connection 

even if the external auger has run for 

four times its operating time.

1. there are pellets in the store.

2. pellets have not accumulated in the 

drop pipe.

3. the level switches function well.

4. the inclination of the drop pipe is not 

too steep (over 45º) or too gentle.

5. the motor shaft rotates the auger 

and the external auger motor func-

tions well.

1. Add pellets and drive the ex-

ternal auger until the pellets ar-

rive at the upper connection of 

the burner. Perform start-up.

2. Adjust the operating time of 

the external auger according to 

the adjustment example

3. Check the operation of the 

level switches from the Burner 

Adjustments menu. The value 

should decrease below the one 

in brackets. After this, the ex-

ternal auger should turn on. 

When the auger stops, the value 

should be 99%.

Alarm blocked pellets

The flame detection system has not de-

tected any flames for 10 minutes and 

the level switch has not asked for more 

pellets. In other words, the burner head 

has run out of pellets and the flame has 

gone out.

1. the level switch eyes are clean (dust).

2. the level switch functions correctly.

3. the burner wheel is fastened and the 

chain is in good state.

4. pellets arrive at the combustion 

vessel.

5. the flame detection sensor func-

tions well.

6. the feeding auger, blocking feeder 

and auger burner rotate and are not 

blocked due, for example, to a foreign 

object.

If there is no fuel in the upper 

connection of the burner, check 

the cable connections of the 

level switches. If this does not 

help, wipe the level switches 

clean. If the external feed of the 

burner does not start in spite of 

this or the level switches must 

be cleaned all the time, they 

may be defective and the instal-

ler should have a look at them. 

A possible foreign object in the 

pellet fuel must be removed if it 

gets stuck in the blocking feeder 

or in one of the feeding augers. 

Remove the upper connection 

and take out the possible fo-

reign object from the feeding 

auger or blocking feeder.

 

ALARMS AND TROUBLESHOOTING

Alarm message / Cause

Check that

Procedure

Alarm boilersensor

The boiler water temperature sensor is 

detached

the boiler sensor is in place and the wi-

res are intact.

If the boiler sensor wire is not 

connected or is broken, the sen-

sor shows the reading 0°C and 

the alarm is activated.

Alarm max flue gas

The flue gas temperature has exceeded 

the alarm limit.

1. the bypass damper of the boiler is 

in place.

2. the flue gas sensor is in the flue gas 

channel.

1. Put the bypass damper in 

place
2. Place the flue gas sensor in 

the flue gas channel.

Alarm max thermostat

 

The boiler water temperature sensor 

shows more than 99 °C.

1. the circulation pump is on

2. the set boiler water temperature

1. Switch the circulation pump 

on.

2. The maximum set temperatu-

re for boiler water is 95ºC. Ho-

wever, the temperature may rise 

above this limit due to residual 

heat. In this case, decrease the 

setting. 

The cause of overheating must 

be found out before restarting.

Alarm Fan tacho

The fan is not rotating

1. The fan is rotating 

The tachometer monitors the 

operation of the blower. If it 

detects that the blower is not 

rotating, an alarm is given and 

the burner stops. However, if the 

blower is functioning, the fault 

may be in the tachometer. The 

tachometer can be switched off 

from the Accessories menu.

Alarm cleaning

The burner gives a warning when it is time to clean the burner head. The 

time is calculated from the augur’s operating time. The interval can be set in 

the Service menu. The setting 0 means that the function is off.

Alarm ash removal

The burner gives a warning when it is time to empty the ash box. 

The time is calculated from the augur’s operating time. The interval can be 

set in the Service menu. The setting 0 means that the function is off.

Summary of Contents for Biomatic+ 20

































Reviews: