Ariterm PX50 Direction For Installation And Use Download | Manualshive

Page: 11 / 16

background image

PELLET STOKER KMP PX50

ARITERM SWEDEN AB

Installation Instructions -

2007.12.14 - 11/16

Outer tube

Inner tube

Pellet stop

Rear housing

Igniter console

Ignitor element tube

Transformer

Blower

Control panel

Connectors

Feeding tube

Cut-out thermostat

Exploded view / Technical data

Technical data

Dimensions outside boiler (b x h x d) ........ 300 x 310 x 300 mm
Dimensions inside boiler (Ø x l) ........................ Ø180 x 200 mm
Efficiency ..................................................................... ca 95%
Output maximum .......................................................... 50 kW
Output minimum .......................................................ca 20 kW
Voltage ...................................................................... 230 VAC
Power consumtion (mean under power) ...........................50 W
Weight ............................................................................12 kg
Length standard screw feeder ......................................... 1,7 m

Accessories and fittings

• Adaptor plate
• Adaptor plate with flange
• Overheat cut-out thermostat for boiler
• Longer screw feeder
• Suspension chain for screw feeder
• Ash separator for vacuum cleaner

«
...
9
10
11
12
13
...
»

Summary of Contents for PX50

















Reviews:

No comments

Related manuals for PX50

Brand: Warmington Pages: 26

Brand: Oilon Pages: 58

Brand: Baxi Pages: 64

Brand: Masport Pages: 20

Brand: RAMBO Pages: 32

Brand: Planika Pages: 7

Brand: Planika Pages: 37

Brand: Cuenod Pages: 60

Heatranger 8120K

Brand: Rayburn Pages: 33

Brand: baltur Pages: 46

Brand: MUT Pages: 24

Brand: hestan Pages: 11

ASPIRE AEB121-LP

Brand: hestan Pages: 40

Brand: hestan Pages: 60

Brand: hestan Pages: 68

Brand: hestan Pages: 72

Brand: Giersch Pages: 4

Brand: Giersch Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands