III. Operation of Power PDA Cradle
Note: In order to use your PDA for satellite navigation, you must have a GPS
receiver and have GPS map software loaded onto your PDA.
After cradle is mounted in the desired position in your vehicle:
1. Plug cradle power cord into the vehicle cigarette lighter socket or
12V power supply.
2. Connect the Charging/Data cord for your PDA -- one end into the
USB PDA slot on the cradle and the other end into the serial port
of your PDA.
3. Connect the audio cord from the 3.5mm speaker jack on the top
of the cradle to the 3.5mm headphone jack on your PDA. If the
headphone jack on our PDA is 2.5mm you will need a special
audio adapter.
4. For satellite navigation: Make sure you have a GPS receiver, such
as Options A, B or C below:
Option A: Connect a mouse-type serial GPS receiver to the RJ12
jack on the top of the cradle (RJ12-to-PS2 adapter
cables are available if needed). This jack will power
your mouse-type receiver and also transfer data
to the PDA.
Option B: Use a Bluetooth GPS Receiver. No cable connection is
necessary. However, for your convenience, Bluetooth
GPS receivers can be charged from the Bluetooth
charging jack on the side of the cradle.
Option C: If your PDA has its own built-in GPS receiver, then no
additional connections are needed.
Turn on your PDA and access your GPS map software program.
5.
Important Safety Notice:
Most GPS software has built-in voice
navigation to allow you to keep your eyes on the road while
driving. If you need to study the map on your PDA, stop the car
and pull into the side of the road first.
IV. Trouble Shooting
1. PDA is not being charged.
- Make sure cradle power cord is connected to 12V lighter
socket. The Red LED indicator on the bottom of the cradle
should be illuminated.
- Make sure the serial cable from cradle to PDA is properly
connected.
2. Data is not being received from the GPS receiver.
- Check the GPS settings on your map software. Should be set
to ComPort 1.
- Make sure the serial cable from cradle to PDA is properly
connected.
- If using the RJ12 jack, make sure the cable is connected
properly.
3. Speaker not working or sound too low or too high.
- Make sure audio cord is connected properly.
- Adjust volume control on side of cradle.
- Adjust volume setting on your PDA.
V. Specifications
Note: Specifications are subject to change without notice.
Power Input 12V-24V DC
Input Power Cord Fixed car cord; plugs into vehicle
lighter socket
PDA Data & Charging Slot: USB 5.2V, 1.2 AH DC
Accessory Power Slot: USB 5.2V, 0.6 AH DC
Aux. DC Out 4.0 Jack, 5.2V, 0.6 AH DC
Speaker 2.0 Watt
Audio In: 3.5 mm jack
Cradle Dimensions 5” x 2” x 3
1/8
” (wings closed)
or 4
5/8
” (fully extended)
Weight (cradle only) 6.5 oz.
A
RKON
P
OWERED
PDA M
OUNT
I N S T R U C T I O N S
COM 1
COM 2
COM 3
COM 4
COM 5
COM 6
COM 7
COM 8
COM 9
Bluetooth
Receiver
COM 6
Serial Type
GPS Receiver
to PS2 Adapter
or
Optional RJ45
GPS Port
COM 1
GPS Options / COM Ports
Compact
Flash
Card
COM5
Copyright © 2004 All rights reserved
These instructions, including all photographs and illustrations are protected under international
copyright laws, with all rights reserved. None the material contained herein, may be reproduced
without the express written consent of the manufacturer.
Trademarks
Product names mentioned herein are used for identification purposes only and may be trademarks
and/or registered trademarks of their respective companies.
Limitation of Liability
While reasonable efforts have been made to ensure the accuracy of these instructions and
distributor assume no liability resulting from errors or omissions, or from the use of the information
contained herein.
Arkon Resources, Inc.
20 La Porte Street Arcadia, CA 91006
626.254.9005 Phone | 626.254.9266 Fax
www.arkon.com
