ARM Cortex-M3 DesignStart Technical Reference Manual Download

Page: 62 / 410

Programmer’s Model

2-14

ARM DDI 0337G

Non-Confidential

Unrestricted Access

Compare negation of register value with another register value

CMN <Rn>, <Rm>

Compare immediate 8-bit value

CMP <Rn>, #<immed_8>

Compare registers

CMP <Rn>, <Rm>

Compare high register to low or high register

CMP <Rn>, <Rm>

Change processor state

CPS <effect>, <iflags>

Copy high or low register value to another high or low register

CPY <Rd> <Rm>

Bitwise exclusive OR register values

EOR <Rd>, <Rm>

Condition the following instruction

Condition the following two instructions

Condition the following three instructions

Condition the following four instructions

IT <cond>

IT<x> <cond>

IT<x><y> <cond>

IT<x><y><z> <cond>

Multiple sequential memory word loads

LDMIA <Rn>!, <registers>

Load memory word from base register a 5-bit immediate offset

LDR <Rd>, [<Rn>, #<immed_5> * 4]

Load memory word from base register a register offset

LDR <Rd>, [<Rn>, <Rm>]

Load memory word from PC a 8-bit immediate offset

LDR <Rd>, [PC, #<immed_8> * 4]

Load memory word from SP a 8-bit immediate offset

LDR, <Rd>, [SP, #<immed_8> * 4]

Load memory byte [7:0] from register a 5-bit immediate offset

LDRB <Rd>, [<Rn>, #<immed_5>]

Load memory byte [7:0] from register a register offset

LDRB <Rd>, [<Rn>, <Rm>]

Load memory halfword [15:0] from register a 5-bit immediate offset

LDRH <Rd>, [<Rn>, #<immed_5> * 2]

Load halfword [15:0] from register a register offset

LDRH <Rd>, [<Rn>, <Rm>]

Load signed byte [7:0] from register a register offset

LDRSB <Rd>, [<Rn>, <Rm>]

Load signed halfword [15:0] from register a register offset

LDRSH <Rd>, [<Rn>, <Rm>]

Logical shift left by immediate number

LSL <Rd>, <Rm>, #<immed_5>

Logical shift left by number in register

LSL <Rd>, <Rs>

Logical shift right by immediate number

LSR <Rd>, <Rm>, #<immed_5>

Logical shift right by number in register

LSR <Rd>, <Rs>

Table 2-4 16-bit Cortex-M3 instruction summary (continued)

Operation Assembler

Summary of Contents for Cortex-M3 DesignStart













































































































































































































































































































































































































Search results

Summary of Contents for Cortex-M3 DesignStart

Reviews:

Related manuals for Cortex-M3 DesignStart

Brands by name

Popular brands

ARM Cortex-M3 DesignStart, Technical Reference Manual

Search results

Summary of Contents for Cortex-M3 DesignStart

Reviews:

Related manuals for Cortex-M3 DesignStart

Brands by name

Popular brands