background image

 

Page 12 

VI. Operation Warnings 

 

1.  Do not use a sharp object or fingernail to press on the 

AromaMist

AromaMist

AromaMist

AromaMist

 

pump switch.  

Sharp objects will penetrate the face plate and damage the aroma switch. 

 
2.  Do not pump unapproved aroma oils with the 

AromaMist

AromaMist

AromaMist

AromaMist

 pump system.  Use of 

foreign oils may pose serious health hazards or damage to equipment. 

 
3.  Check with a physician prior to using the 

AromaMist

AromaMist

AromaMist

AromaMist

 pump system if you are 

pregnant, have a coronary condition, are in poor health, are using medications or 
drugs, have allergies or are being treated for any other medical conditions. 

 

4.  Children under the age of 17 should not use a steambath. 

 

5.  Exit the steam shower immediately if you feel uncomfortable, faint, dizzy or tired. 

 

6.  Aroma oil residue, steam shower condensation and moisture will cause the 

steam room floor and other surfaces to become slippery.  Installation of non-skid 
floor materials and caution while walking is always recommended. 

 

7.  Do not walk near or by steam outlet head during steam shower operation. 

 

8.  Do not activate the 

AromaMist

AromaMist

AromaMist

AromaMist

 pump while the steam generator is off or not 

producing steam.   If pump is accidentally activated with steam generator off, 
operate steam generator for 10 minutes with aroma switch in the off position to 
flush the steam line.  Follow with water spray to wash the steam shower floor of 
excess aroma oil residue. 

 

9.  Aroma oil is an oil-based product which will make the steam shower floor 

slippery.  It is important to wash down floor with water immediately after each use 
and use caution while walking. 

 

10. Should you have any questions about the safe installation or operation of the 

AromaMist

AromaMist

AromaMist

AromaMist

 pump system, we encourage you to call us at (847) 465-8990. 

 
 

Summary of Contents for AI-5
















Reviews: