background image

 

Page 

3

 

I. Introduction 

Congratulations, you have just purchased the world’s most advanced aroma oil 
metering pump, the 

AromaMist

AromaMist

AromaMist

AromaMist

 

pump. 

 
This instruction manual covers all facets of the installation and operation of the 

AromaMist

AromaMist

AromaMist

AromaMist

 

pump including unpacking, mounting, electrical, plumbing, control, pump 

connections, and start-up. 
 
All information in these instructions is based on the latest product information available 
at the time of publication.  Accurate Industries Et Al., Inc. reserves the right to make 
changes at any time without notice.  Please read this manual completely before 
proceeding. 
 
Observe safety protocols and heed all warnings and precautions for safe and efficient 
installation and operation of the 

AromaMist

AromaMist

AromaMist

AromaMist

 pump.

 

 

WARNING: It is recommended to have a certified licensed electrician 
and plumber install the 

AromaMist

AromaMist

AromaMist

AromaMist

 

pump system. 

 
 

II.  Safety and Operating Information 

 

CAUTION: Please read this manual in its entirety prior to installing or 
operating the 

AromaMist

AromaMist

AromaMist

AromaMist

 pump system. 

 

A. Chemical Compatibility 

AromaMist

AromaMist

AromaMist

AromaMist

 

metering pumps are designed to work with 

AromaMist

AromaMist

AromaMist

AromaMist

 oils only.  

Failure to do so may void the warranty or pose serious health hazards. 
 

B. Safety Equipment and Preparation 

Always wear the proper protective clothing and gear when working around 
chemicals and chemical metering pumps. Safety glasses, gloves, and aprons can 
prevent accidental exposure to chemicals. 
 

C. In Case of Accident 

If a chemical spillage occurs, consult the Material Safety Data Sheet (MSDS) for 
specific instructions regarding the chemical being used. 

 

D. Liquids Under Pressure 

Liquids under pressure can present a special hazard when a line or seal is 
punctured resulting in the spraying of chemical many yards away. 

 

E. Safe Installation 

Do not install the 

AromaMist

AromaMist

AromaMist

AromaMist

 

pump system without reading and understanding the 

Operation Warning section (V) and Operation section (VII) of this manual. 

Summary of Contents for AI-5
















Reviews: