background image

REVERSE SMART AEB OPERATING MANUAL 

 

Page 

2

 of 

12

 

July 2017 
 

DISCLAIMER 

1.  The Supplier does not warrant that the device will eliminate risk of collision.  The device is primarily a 

driver aid intended to warn of proximity to objects giving rise to potential collision hazard, it does NOT 
prevent collision. 

2.  The device is not a substitute for driver attention, skill and judgement. 

3.  The device is not a substitute for driver involvement and action.  At all times the vehicle remains under 

the control of the driver, notwithstanding the operation of the device. 

4.  The device may not be functional in all situations and the operator must consult and use the device in 

accordance  with  the  operating  parameters  as  set  out  on  the  Reverse  Smart  AEB  operation  Manual 
(“the Manual”) as supplied with the device. 

5.  The device should only be used by drivers who have received operational training in accordance with 

the requirements of the Manual.  No warranty as to operational effectiveness is provided in the event 
of use by a driver who has not been trained in accordance with the provisions of the Manual. 

6.  The  device  must  be  installed,  serviced,  calibrated  or  adjusted  at  all  times  in  accordance  with  the 

requirements set out in the Manual.  No warranty is provided as to the operational effectiveness of the 
device in the event of failure to install or service in accordance with the provisions of the Manual. 

7.  The device is simply a driver aid in conjunction with other safety systems and represents a supplement 

to rather  than  substitute for  driver  attention, care,  skill,  judgement  and  common sense.   At  all  times 
when using the device the driver must continue to take all usual precautions of a professional driver 
ordinarily adopted in the applicable driving conditions. 

8.  Where  the  Manual  provides  that  the  device  should  be  operated  in  conjunction  with  other  safety 

procedures and devices then no warranty is provided as to the performance or otherwise pf the device 
in the event that it is not used in conjunction with such other safety procedures and devices. 

 

 

 

 

Summary of Contents for REVERSE SMART













Reviews: