background image

WARRANTY INFORMATION 

 

Limited Warranty: 

 

Applied Research and Technology will provide warranty and service for this unit in accordance with 
the following warrants: 
 
Applied Research and Technology, (A R T) warrants to the original purchaser that this product and 
the components thereof will be free from defects in workmanship and materials for a period of three 
years from the date of purchase. Applied Research and Technology will, without charge, repair or 
replace, at its option, defective product or component parts upon prepaid delivery to the factory 
service department or authorized service center, accompanied by proof of purchase date in the form 
of a valid sales receipt. 

 

Exclusions:  

 

This warranty does not apply in the event of misuse or abuse of the product or as a result of 
unauthorized alterations or repairs. This warranty is void if the serial number is altered, defaced, or 
removed. 
 
A R T reserves the right to make changes in design or make additions to or improvements upon this 
product without any obligation to install the same on products previously manufactured. 
 
A R T shall not be liable for any consequential damages, including without limitation damages 
resulting from loss of use. Some states do not allow limitations of incidental or consequential 
damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific 
rights and you may have other rights, which vary from state to state. 
 
For units purchased outside the United States, an authorized distributor of Applied Research and 
Technology will provide service. 

 15  

 

Summary of Contents for Voice Channel





















Reviews: