background image

9     Legal Notice

EXCEPT FOR ANY WRITTEN EXPRESS WARRANTY WE MAY SEPARATELY OFFER TO YOU, 

AND TO THE EXTENT PERMITTED BY LAW, THIS PRODUCT IS PROVIDED “AS IS” AND WE 

SPECIFICALLY DISCLAIM ALL EXPRESS, STATUTORY AND IMPLIED WARRANTIES, 

INCLUDING, BUT NOT LIMITED TO, WARRANTIES OF MERCHANTABILITY, FITNESS FOR A 

PARTICULAR PURPOSE, NON-INFRINGEMENT AND AGAINST HIDDEN OR LATENT 

DEFECTS.  IF WE CANNOT LAWFULLY DISCLAIM STATUTORY OR IMPLIED WARRANTIES, 

THEN TO THE EXTENT PERMITTED BY LAW, ALL SUCH WARRANTIES SHALL BE LIMITED 

IN DURATION TO THE DURATION OF ANY WRITTEN EXPRESS WARRANTY WE MAY 

SEPARATELY OFFER TO YOU, AS APPLICABLE, AND TO REPAIR OR REPLACEMENT 

SERVICE.  SOME JURISDICTIONS DO NOT ALLOW LIMITATIONS ON HOW LONG A 

STATUTORY  OR IMPLIED WARRANTY LASTS, SO  THE ABOVE LIMITATION MAY NOT 

APPLY TO YOU. WE ARE NOT RESPONSIBLE FOR DIRECT, SPECIAL, INCIDENTAL OR 

CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR UNDER 

ANY OTHER LEGAL THEORY. IN SOME JURISDICTIONS THE FOREGOING LIMITATION 

DOES NOT APPLY TO DEATH OR PERSONAL INJURY CLAIMS, OR ANY STATUTORY 

LIABILITY FOR INTENTIONAL AND GROSS NEGLIGENT ACTS AND/OR OMISSIONS, SO THE 

ABOVE EXCLUSION OR LIMITATION MAY NOT APPLY TO YOU. SOME JURISDICTIONS DO 

NOT ALLOW THE EXCLUSION OR LIMITATION OF DIRECT, INCIDENTAL OR 

CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSION OR LIMITATION MAY NOT 

APPLY TO YOU.

8.2     Copyright and Trademark

Copyright © 2015 Art2Wave, Inc.  All rights reserved.  The contents of this Installation Guide are 

the copyrighted and proprietary property of Art2Wave, Inc.  Reproduction, distribution or 

modification without the express, written permission of Art2Wave, Inc. is not permitted.   

“Art2Wave” is a trademark of Art2Wave, Inc.  All other trademarks are the property of their 

respective owners.

8.3     Open Source Code

Certain Art2Wave products include open source software code subject to the GNU General 

Public License (GPL) and other Open Source Licenses. For more information, see:

http://art2wave.com/opensource

Summary of Contents for ap20













Reviews: