background image

Centellis 2000 User Card 10GE Hardware

Centellis 2000 User Card 10GE with Telco Alarm Installation and Use (6806800M46C)

35

2.5

Installing and Removing SFP/ SFP+ Modules

This section describes how to install and remove SFP/SFP+ modules.

Table 2-1

 provides the list of SFP/SFP+ modules tested to use with Centellis 2000 User Card.

Eye Damage
Optical SFP/SFP+ modules may emit laser radiation when no cable is connected. 
Avoid staring into open apertures to avoid damage to your eyes. 

Personal Injury and Damage of the RTM and SFP/SFP+ Modules 
Installing and using SFP/SFP+ modules which are not fully certified and which do not meet 
all relevant safety standards may damage the RTM and the SFP/SFP+ modules and may lead 
to personal injury.
Only use and install SFP/SFP+ modules which are fully certified and which meet all relevant 
safety standards. 

Personal Injury
Optical SFP/SFP+ modules may be classified as laser products. When installing and using any 
of these SFP/SFP+ modules, the regulations which correspond to the respective laser class 
apply to the whole RTM. Not complying to these regulations, may lead to personal injury. 
When installing and using optical SFP/SFP+ modules which are classified as laser products, 
make sure to comply to the respective regulations. 

SFP/SFP+ modules can be installed or removed  while the RTM is powered and non-powered. 
The presence and also the type of SFP/SFP+ modules is automatically detected. 

Table 2-1 SFP/SFP+ Modules

Part Number

Vendor

TRX10GVP2010EP01

Merge Optics             

Summary of Contents for Centellis 2000 Series





























































Reviews: