background image

9

retracting. When in Conference model, the microphone will always be 
active and both the light ring and the access to the push button on 
the cover plate will be available via GPI and GPO for remote control.

DynamicTalk is available in 3 sizes:  for 400 mm, 500 mm and 600 
microphones. The system can  be adjusted to the exact length of the 
microphone via AHnet and AHlink. The AHlink is an excellent tool to 
diagnose, verify and configure DynamicTalk.

Features

•  Universal lift system for gooseneck XLR 3 pin microphones
•  Stainless steel cover plate with 3 buttons
•  LED lighting ring to indicate microphone status, 360º
•  Serial control and remote diagnosis 
•  Individual addressing 
•  AH-AMMC Auto Mechanical Movement Calibration 
•  PA and Conference working modes

Box Contents

Before the installation of your DynamicTalk, please check the contents 
of the shipping box, it must contain the following items:
•  DynamicTalk
•  Power cord
•  Power supply 100-240Vac, 50-60Hz. Output 12V 
•  User Manual

Important Note: This device can only work with the power supply 
included in the shipping box. This power supply can not be replaced by 
any other rather than the original one.

Caution! Never use this monitor in horizontal position.

APPLICATIONS

Summary of Contents for AHDTL

























Reviews: