background image

 3 of 8

 

1.

 

Park the vehicle on a flat, level surface.

 

2.

 

Open the tailgate. Use a 10mm socket to remove the 

left and then right tail lights.  See Fig. 2.

 

3.

 

Per Fig. 3, disconnect the left and right tail lights from 

the vehicle.  Set the tail lights with mounting 

hardware aside for re

-

use in Step 12 on the next 

page.

 

4.

 

Close the tailgate and tilt the bed back using the 

vehicle

s bed latch.  See Fig. 4.

 

5.

 

Using a T30 Torx bit, remove (4) screws from the 

bottom of the left and right sides of the bed.  Set 

removed hardware aside for re

-

use. See Fig. 5.

 

6.

 

Using a T40 Torx bit, remove the screw next to the 

latch handle on the left side and right side of the bed. 

Set removed hardware aside for re

-

use. See Fig. 6.

 

 

 

 

Fig. 5; Remove Underside Screws on the Side Panel

 

 

 

It is the user

s responsibility to ensure that installation of this 

product does not affect the functionality of the vehicle ROPS, 

tires, or any other safety feature of the vehicle. Failure to do 

so may result in injury or death. Due to the many features on 

the UTV vehicle, the Bed Mounted Tool Bar or some of its 

quick removal accessories may interfere with dump bed 

operation, fender flares, or tires. If necessary, the quick

-

release Cam Lever Latches on the ROPS Mounted Tool Bar 

accessories allow a given accessory to be quickly removed 

and relocated to a non

-

interfering location.

 

Artillian strives to continuously improve our products. As such, the 

actual product may vary from the images shown throughout this 

manual. 

 

Fig. 2; Remove Left Tail Light

 

WARNING

 

Fig. 3; Disconnect Left Tail Light

 

Fig. 4; Tilt Bed Back

 

Fig. 6; Remove Screw Next to Latch Handle

 

Remove Hardware (4 places per side)

 

Remove Hardware

 

Remove Hardware

 

Disconnect Connector

 

KIT INSTALLATION

 

Note: If installing 

The Artillian UTV Bed Mounted Tool 

Bar 

on the Polaris Ranger 1000, proceed with the 

following steps 1

-

12. If installing on the Gravely Atlas JSV 

3400SD, skip to page 5 and start with step 13.

 

Summary of Contents for 1UTVTBPR









Reviews: