background image

MELLES GRIOT 

5

Chapter 2

For Your Safety

2.1

Safety Information

For the continuing safety of the operators of this equipment, and the protection of the
equipment itself, the operator should take note of the Warnings, Cautions and Notes
throughout this handbook and, where visible, on the product itself.

The following safety symbols may be used on the equipment:

Read the operating instructions before use

Connection to Earth

High voltages present

Earth point

The following safety symbols may be used throughout the handbook:

Warning

. An instruction which draws attention to the risk of injury or death.

Caution

. An instruction which draws attention to the risks of damage to the product,

process or surroundings.

Note

. Clarification of an instruction or additional information.

The Equipment, as described herein, is designed for use by personnel properly
trained in the use and handling of mains powered electrical equipment. Only
personnel trained in the servicing and maintenance of this equipment should remove
its covers or attempt any repairs or adjustments.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Melles Griot 17MMR001































Reviews: