background image

CAUTION: Only Aruba-approved power cords may be used with Aruba devices. To access the power

cord information for your switch, see the latest edition of the Aruba Instant On 1930 Switches Installation

and Getting Started Guide. Lost or damaged power cords must be replaced only with Aruba-approved

power cords. If your installation requires a different power cord than the one supplied with the switch

and/or power supply, be sure that the cord is adequately sized for the current requirements of the

switch. In addition, be sure to use a power cord displaying the mark of the safety agency that defines

the regulations for power cords in your country/region. The mark is your assurance that the power cord

can be used safely with the switch and power supply.

WARNING: Do not use a damaged or nonrecommended power cord with your switch. Using such

power cords voids the switch and power supply warranty. It can also cause serious electrical problems,

including injury or death to personnel, and damage to the switch and other property. If you cannot

verify that you have a power cord approved for use with your switch model, contact your authorized

Aruba dealer or sales representative for assistance.

WARNING: Remove the power cord from the switch before mounting or dismounting the switch.

Environmental specifications

Table 1: Environmental specifications for all 1930 switch models

Requirement

Value

Operating temperature

32°F to 104°F (0°C to 40°C)

Operating relative humidity

15% to 95%

Non-operating temperature

-40°F to 158°F (-40°C to 70°C) up to 15000 ft

Storage relative humidity

15% to 95%

Max operating altitude

10000 feet (3 km) Max

Max non-operating altitude

15000 feet (4.6 km) Max

Switch

Dimensions (L x W x H)

Weight

Aruba Instant On 1930 8G 2SFP Switch

(JL680A)

6.4" x 9.9" x 1.72"

(16.2 x 25.35 x 4.35 cm)

2.60 lb

(1.18 kg)

Aruba Instant On 1930 8G Class4 PoE 2SFP

124W Switch (JL681A)

10.12" x 9.9" x 1.72"

(25.7 x 25.35 x 4.35 cm)

4.17 lb

(1.89 kg)

Aruba Instant On 1930 24G 4SFP/SFP+ Switch

(JL682A)

8.94" x 17.43" x 1.72"

(22.7 x 44.25 x 4.35 cm)

5.35 lb

(2.43 kg)

Aruba Instant On 1930 24G Class4 PoE

4SFP/SFP+ 195W Switch (JL683A)

10.56" x 17.43" x 1.72"

(26.8 x 44.25 x 4.35 cm)

7.65 lb

(3.47 kg)

Aruba Instant On 1930 24G Class4 PoE

4SFP/SFP+ 370W Switch (JL684A)

10.56" x 17.43" x 1.72"

(26.8 x 44.25 x 4.35 cm)

8.10 lb

(3.67 kg)

Table Continued

Page 4

Summary of Contents for Instant On 1930 Series









Reviews: