background image

 

    BEAVER  8・8F   

 

 

 

6

 

 

CONTENTS 

1. COMPONENTS OF THE MACHINE 

1) Main Parts-----------------------------------------------------------------------------------  7 

2) Specifications------------------------------------------------------------------------------- 9 

3) Optional Accessories---------------------------------------------------------------------  9 

4) Saw Blade and Cutting Load Selecting Chart by material ---------------------- 11 

2. INSTALLATION 

1) Carrying the Machine---------------------------------------------------------------------- 12 

2) Installation------------------------------------------------------------------------------------ 12 

3) Proper working environment-------------------------------------------------------------13 

3. OPERATION 

1) Replacement the Saw Blade------------------------------------------------------------ 14 

2) Adjustment of Blade Guide F ----------------------------------------------------------- 15 

3) Clamp the material------------------------------------------------------------------------- 15 

4) Adjustment of Cutting speed------------------------------------------------------------ 16 

5) Cutting----------------------------------------------------------------------------------------- 17 

6) Removing the Workpiece----------------------------------------------------------------- 17 

4. MAINTENACE & INSPECTION 

1) Replacement of Parts 

1-1) Replacement the Pulley Rubber--------------------------------------------------- 19 

2) Correction Procedure for Oblique Cutting (Flat Vise type) ---------------------- 20 

3) Daily Inspection and Maintenance----------------------------------------------------- 20 

5. BEFORE ASKING FOR REPAIRS------------------------------------------------------ 22 

6. ELECTRICAL WIRING DIAGRAM------------------------------------------------------ 24 

  

  

 
 
 
 
 
 

  

  

  

 

Summary of Contents for BEAVER 8





























Reviews: