background image

 

Page 7

 

Installation

 

Powering Up the Hub

 

This section explains how to power up the hub for functionality. 
If you are installing more than one hub, you may want to repeat 
this procedure for each hub before attaching any device or net 
work connections.

To power up the hub, do the following steps:

 

1

 

Make sure the power toggle switch is in the 

 

off

 

 position on 

the back panel. 

 

 

Note: Never remove or insert the power cords with the 
power switch turned 

 

on

 

.

 

 

2

 

Attach the power cords to the sockets on the backpanel 
and connect them to an AC outlet.

 

3

 

 Turn 

 

on

 

 the power switch.

 

Checking the Fuse

 

A blown fuse usually indicates a serious problem in the power 
supply. Contact technical support to help you determine the 
cause and whether you should replace the fuse, or return the orig-
inal for testing and servicing.

To check the fuse, do the following steps:

 

1

 

Make sure the power is turned 

 

off

 

 and unplug the hub.

 

2

 

Insert a small screwdriver under the fuse faceplate located 
on the hub’s front panel and lift if off.

 

3

 

Check the fuse to see if it has blown.

A back-up fuse is stored in the fuse holder (small black 
box) that is attached to the visible fuse.

 

 

Note: Always use the same type of fuse (4A/250V) that 
came with the chassis. Failure to do so may result in 
damage to the hub.

Summary of Contents for AsanteHub 2072RPU











Reviews: