Asco 335 Installation & Operation Manual Download

Page: 14 / 16

For access to self-service tools and chat support visit se.com/us/en/work/support or call 1-888-778-2733 for technical assistance

IO-70065

01/2020

ASCO 335 Surge Protective Device (SPD)

Operation

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe

electrical work practices. See NFPA 70E, NOM-029-STPS or CSA Z462.

•

This equipment must only be installed and serviced by qualified

electrical personnel.

•

Turn off all power supplying this equipment before working on or inside

equipment.

•

Always use a properly rated voltage sensing device to confirm power is

off.

• Replace all devices, doors and covers before turning on power to this

equipment.

•

This equipment must be effectively grounded per all applicable codes.

Use an equipment-grounding conductor to connect this equipment to the

power system ground.

Failure to follow these instructions will result in death or serious injury.

DANGER

LED Status Indicators

Audible Alarm

Diagnostic LEDs are located on the front of the ASCO 335 SPD device.

They operate as follows:

• Verify that all phase voltages are present. If any of the LEDs are not

illuminated, the device may not be installed correctly. Check the power

supply and service voltage. Upon energizing the SPD, check the LED status.

• If all of the LEDs are illuminated, surge suppression is operating.

• If one or more LEDs are not illuminated, there is a loss of surge

suppression on that phase.

•

If an inoperative condition occurs the device must be replaced by qualified

electrical personnel.

The audible alarm does not have a silence switch. Silence the alarm by

removing power from the SPD. The alarm indicates that the device needs

replacement by qualified electrical personnel.

Light 1

Light 2 Alarm Red Audible Alarm

Corrective Action

Out

Off

Reset Breaker if re-opens

Replace Unit

Green

No action

Out

Green

Blinks

Sounds

Replace Unit

Green

Out

Blinks

Sounds

Replace Unit

Green

Blinks

Sounds

Check Neutral to Ground

Connection before

Replacing Unit

Summary of Contents for 335

















Search results

Summary of Contents for 335

Reviews:

Related manuals for 335

Brands by name

Popular brands

Asco 335, Installation & Operation Manual

Search results

Summary of Contents for 335

Reviews:

Related manuals for 335

Brands by name

Popular brands