background image

13

ADC-02CF

TROUBLESHOOTING GUIDE

Seat or backrest locks up and cannot be raised or lowered:

• 

Refer to 

Clearing Hydraulic Lockups

 on page 4.

When preparing the chair for shipping, the frame posts 

won’t lower all the way to the floor:

• 

Press down and hold the selector lever in the SEAT LOWER 

position and press and hold down the lift lever simultaneously.

Chair’s hydraulics feel sluggish or jerky when raising or 

lowering the seat or backrest:

• 

Refer to 

Purging Air from the Hydraulic System

 on page 5.

• 

Refer to 

Adding Oil to the Hydraulic System

 on page 7.

Oil is leaking from the hydraulic system:

• 

NOTE: Small amounts of oil leaking after prolonged use are 

normal.

• 

Tighten all hydraulic hose fittings and port plugs on the 

hydraulic pump. If leakage persists, contact Aseptico custom‑

er service about returning the hydraulic assembly for repairs.

WARRANTY

Aseptico warrants this product against defects in material or work‑

manship for a period of two (2) years, from date of original invoice.  

Aseptico’s sole obligation under product warranty is (at its sole op‑

tion and discretion) to repair or replace any defective component 

or product in part or whole.  Aseptico shall be the sole arbiter of 

such action.

In the event of alleged defect under warranty, the purchaser 

is to notify Aseptico’s customer service department promptly.  

Customer service will provide instructions, usually directing that 

the product be returned for service.  Shipment to Aseptico and the 

cost thereof is always the responsibility of the purchaser.

Accidental misuse, inappropriate installation, or failure to perform 

directed maintenance voids the warranty. Deliberately defacing, 

modifying, or removing the serial number voids the warranty.

Aseptico does not assume, under this warranty, any risks or liabili‑

ties arising from the clinical use of its products, whether or not such 

use involves coincidental utilization of products manufactured by 

others.

REPAIRS

Aseptico repairs carry a ninety (90) day limited warranty against 

defects in material and workmanship. This warranty pertains only 

to the specific repair. Any new and different defect in materials or 

workmanship will be treated as a new repair. If the product is not 

covered under warranty, Aseptico offers repair services for a fee.

Summary of Contents for ADC-02CF

















Reviews: