wedge under the jammed log.
• Lower the splitter to push the wedge completely
under the jammed log.
• Repeat the above procedure with increasing wedges
until the log is completely loosened.
Do not knock out the jammed log. Doing so could
damage the machine or drop the log, which could
cause an accident.
CLEaNiNg aND maiNTENaNCE
Regular cleaning is essential for safe operation.
The hydraulic system is a closed system with an oil
tank, an oil pump with a control valve.
Regularly check that the hydraulic connections and
fittings are properly tightened. Tighten if necessary.
The oil tank was filled with high-quality hydraulic oil
at the factory.
The first oil change must be performed after 150
working hours, then every 300 working hours.
Check the oil level regularly. (the machine must be on
a horizontal surface, splitting wedge inserted). If the oil
level is low, it is necessary to top up the oil.
Make sure the oil cap is tightened to prevent leakage.
Oil change
Remove the drain plug
Collect the drained oil in a suitable container (the
amount of oil varies from model to model).
Dispose of drained oil in an environmentally friendly
manner.
Replace the drain plug. Notice! None must enter the
oil tank dirt.
Fill the tank with new hydraulic oil
Observe local waste laws when disposing of industrial
lubricants. The provisions of the law classify used
motor oil as a waste that can only be disposed
of ecologically. Such disposal may be carried out
exclusively by an authorized person who has consent
to the operation of the facility for disposal or further use
of oil from the regional authority.
Used oils can only be disposed of in hazardous waste
mode. Oils cannot be disposed of by pouring into
nature or sewage.
WEDGE SHARPENING
After some time of using the splitter, sharpen its wedge
with a fine file and level the unevenness and damaged
parts around the blade.
TECHNiCaL DaTa aE9SK105-8
Power supply: 230V ~ 50Hz
Power consumption: 1050W
Idle speed: 2800 / min
Splitting force: 8t
Log splitting diameter: 280mm x 520mm
Splitting speed: 10-12m3 / h
Strike speed: 1s
Weight: 75kg
Safety cover Yes
Protection class I.
Subject to changes.
Sound pressure level measured according to EN
60745:
LpA (sound pressure) 78 dB (A) KpA=3
LWA (sound power) 89 dB (A) KwA=3
Take appropriate measures to protect your hearing!
Wear hearing protection whenever the sound pressure
exceeds the level of 80 dB (A).
Weighted effective acceleration according to EN
60745: 3,2 m/s2 K=1.5
Caution: The vibration level may vary during power
tool operation from the declared value depending on
the way the power tool is used and depending on the
following conditions: Method of power tool use and
type of material being cut or drilled, conditions of the
power tool and method of its maintenance, appro
-
priateness of the used accessories and ensuring its
sharpness and good conditions, the strength of handle
gripping, use of anti-vibration equipment, suitability of
the power tool for the purpose for which it has been
designed and compliance with workflows according to
manufacturer‘s instructions.
If this power tool is used in an inappropriate manner, a
hand/shoulder vibration syndrome may appear.
Caution: For clarification, it is necessary to consider
the level of vibrations in specific conditions of use in all
operating modes, e.g. the time when the power tool is
switched off except for the operation time, and when
it idles, i.e. performs no work. This may substantially
decrease the exposition level during the whole operat
-
ing cycle.
Minimize the risk of vibrations, use sharp chisels, drill
and blades.
Keepthe power toolin compliancewith theseinstruc
-
tions and provide for its proper lubrication.
When using the power tool regularly, invest into anti-
vibration equipment.
Do not use the power tool under temperatures lower
than 10°C. Plan your project containing work with the
power tool producing high vibrations carefully and
spread it over more days.
Subject to changes.
ENVirONmENTaL PrOTECTiONWaSTE ma
-
NagEmENT
Power tools, accessories and packaging should be
provided for recycling and not to harm the environment.
Do not dispose of power tools into household waste!
According to Directive 2012/19/EU of the European
Parliament and of the Council on waste electrical and
63
