Asist AE9BS06DN, Instructions For Use Manual

engage in the grinding station mechanism.

REPLACING FOCUS ATTACHMENTS

Press the lever to release the attachment. Simultane

-

ously pull the attachment upwards from the guide rail.

SWITCHING ON

Press button 3 to position „I“ to start the device.

OFF 

Press button 3 to position „O“ to switch off the device.

The device is not intended for continuous operation 

- after 30 minutes of use it must be switched off and 

allowed to cool down completely.

DRILL SHARPENING

With this grinding station, drills with a diameter of 

3-13 mm can be sharpened. 

PREPARATION

1) Attach the drill bit attachment to the side where the 

grinding wheel is located.

2) Remove the drill holder from the drill sharpening 

attachment and insert the drill bit into it. Fix the drill in 

the holder with the nut for fixing the drill so that it fits 

firmly, but can still move in the holder.

3) Insert the holder with the drill bit inserted into the 

setting compartment.

It is essential that the holder fits into the rails of the 

adjusting compartment.

4) Slide the drill forward and rotate it so that it rema

-

ins in the V-shaped groove. The tip of the drill should 

touch the metal stop. The blades must rest on the 

metal sides of the groove.

5) Tighten the nut to secure the drill - fix the drill in 

the holder,

6) Remove the drill holder from the adjustment 

compartment and insert it back into the drill bit at

-

tachment. Make sure that the holder fits into the rails 

in the attachment.

7) Check that the drill blades touch the grinding whe

-

el. If not, repeat the drill alignment described above.

8) The drill can now be sharpened.

FOCUS

1) Switch on the sanding station and move the upper 

part of the drill sharpening attachment to the right and 

left to sharpen both blades.

2) Switch off the sanding station, remove the drill 

holder from the bit, turn it and insert it back into the bit 

so that the opposite side of the cutting edges can be 

sharpened.

3) Repeat the focusing procedure for the same time.

4) Remove the drill holder and check that the cuts 

of both drill grooves are equally sharp. They should 

meet in the middle.

5) Repeat sharpening if any deviations need to be 

corrected.

SHARPENING OF CHISELS AND PLANING KNIVES

With this grinding station, chisels and planing knives 

with a width of 6-51 mm can be sharpened.

Focus angle (15-50 °) can be adjusted by adjusting 

the angle.

Loosen the angle adjustment handle, tilt the support 

plate to the desired angle and tighten the handle.

PREPARATION

1) Attach the drill bit attachment to the side where the 

grinding wheel is located.

2) Place the blade on the support plate so that the 

side of the chisel or planing knife rests on the end of 

the edge of the plate.

The blade is held in place by magnets. To sharpen 

narrow chisels, attach the spacer to the edge of the 

support plate.

3) Check that the plate angle matches the existing 

blade angle. Only in this way can the optimum clam

-

ping angle of the blade be ensured.

4) Make sure that the cutting edge touches the grin

-

ding wheel and that the protective cover is fitted.

FOCUS

1) Switch on the sanding station and move the sup

-

port plate forwards and backwards while holding the 

tool in position. Use constant pressure and focus on 

steady and even movements.

2) While sharpening, slide the blade down toward the 

grinding wheel while maintaining a constant, gentle 

pressure.

3) Remove the workpiece and check that the angle 

and the cutting edge are sharp and even along their 

entire length.

4) Remove any unevenness by continuing to focus.

SHARPENING OF KNIVES AND SCISSORS

With this universal grinding station, all knives and 

scissors with straight blades with a smooth surface 

can be sharpened. Blades with corrugated and spe

-

cial cutting edges will be damaged by grinding.

1) Attach the attachment for sharpening knives and 

scissors to the side where the grinding wheel is 

located.

KNIFE SHARPENING

1) Switch on the sanding station.

2) Insert the knife into one of the notches on the knife 

and scissor attachment so that the cutting edge faces 

the grinding wheel.

3) Slide the blade along the grinding wheel slowly by 

pulling it towards you. Maintain only a slight pressure 

so that the contact with the grinding wheel is maintai

-

ned up to the tip of the blade.

4) Turn the knife and insert it into the opposite notch 

on the attachment. Repeat step 3.

5) Repeat sharpening alternately until the cutting 

edge is sharp and clean.

SCISSOR SHARPENING

1) Switch on the sanding station.

2) Open the scissors completely.

3) Place one of the scissor blades in the notch for 

sharpening the scissors (below on the attachment). 

Hold the scissors fully open and hold the other blade 

on the right side.

4) Pull the blade along the grinding wheel from the 

screw to the tip under constant and gentle pressure.

38