ASROCK ALIVENF5-ESATA2 R3.0 Installation Manual Download

Page: 5 / 26

1.3

Installing Windows

2000 / XP / XP 64-bit / Vista

/ Vista

64-bit With RAID Functions

If you want to install Windows

2000, Windows

XP, Windows

XP 64-bit, Windows

Vista

or Windows

Vista

64-bit on your SATA / SATAII HDDs with RAID functions,

please follow below procedures according to the OS you install.

Before installing Windows

2000 to your system, your Windows

2000 optical

disk is supposed to include SP4. If there is no SP4 included in your disk, please

visit the below website for proper procedures of making a SP4 disk:

http://www.microsoft.com/Windows2000/downloads/servicepacks/sp4/spdeploy.
htm#the_integrated_installation_fmay

1.3.1 Installing Windows

2000 / XP / XP 64-bit With RAID

Functions

If you want to install Windows

2000 / Windows

XP / Windows

XP 64-bit on your SATA

/ SATAII HDDs with RAID functions, please follow below steps.

STEP 1: Set Up BIOS.

Enter BIOS SETUP UTILITY

Advanced screen

IDE Configuration.

Set the “SATA Operation Mode” option to [RAID].

STEP 2: Make a SATA / SATAII driver diskette.

Insert the ASRock Support CD into your optical drive to boot your system.

During POST at the beginning of system boot-up, press <F11> key, and

then a window for boot devices selection appears. Please select CD-ROM

as the boot device.

When you see the message on the screen, “Generate Serial ATA driver

diskette [YN]?”, press <Y>.

Then you will see these messages,

Please choose:

1. Generate AHCI Driver diskette for Windows2000/XP/XP64

2. Generate RAID Driver diskette for Windows2000/XP

3. Generate RAID Driver diskette for WindowsXP64

4. Exit

Reboot system now

Press any key to continue

Please insert a floppy diskette into the floppy drive. Select your required

item on the list according to the mode you choose and the OS you install.

Then press any key.

The system will start to format the floppy diskette and copy SATA / SATAII

drivers into the floppy diskette.

If you want to enable Hot Plug function on eSATAII ports but you install OS

on IDE HDD, please skip step 2.

Summary of Contents for ALIVENF5-ESATA2 R3.0



























Search results

Summary of Contents for ALIVENF5-ESATA2 R3.0

Reviews:

Related manuals for ALIVENF5-ESATA2 R3.0

Brands by name

Popular brands

ASROCK ALIVENF5-ESATA2 R3.0, Installation Manual

Search results

Summary of Contents for ALIVENF5-ESATA2 R3.0

Reviews:

Related manuals for ALIVENF5-ESATA2 R3.0

Brands by name

Popular brands