Assa Abloy Adams Rite EX88 Preparation Manual And Installation Instructions Download

Page: 1 / 10

Page | 1

800.872.3267

800.232.7329

techsupport.adamsrite@assaabloy.com

www.adamsrite.com

EX88 Interlocking Rim Exit Device

Preparation Guide and Installation Instructions

Box Contents

EX88 Interlocking Rim Exit Device

Cylinder and Trim Interface Kit

Mounting Hardware Kit

Frame Kit with Templates

Mounting End Cap Kit

Recommended Installation Tools

Safety glasses

Measuring tape

Level

Pencil

Power drill

Drill bits: 5/32”, 3/4”

Center punch

Phillips screw driver

IMPORTANT NOTE 1: All work must be performed to applicable building, regulatory and life-
safety codes. Please consult local Authority Having Jurisdiction (AHJ) for more information.

IMPORTANT NOTE 2: The Americans with Disabilities Act (ADA) guidelines specify door
hardware be mounted 34”-48” above the finished floor.

Active Push Bar

Filler Plate

Back Bar

Summary of Contents for Adams Rite EX88











Search results

Summary of Contents for Adams Rite EX88

Reviews:

Related manuals for Adams Rite EX88

Brands by name

Popular brands

Assa Abloy Adams Rite EX88, Preparation Manual And Installation Instructions

Search results

Summary of Contents for Adams Rite EX88

Reviews:

Related manuals for Adams Rite EX88

Brands by name

Popular brands