Assa Abloy Adams Rite EX88 Preparation Manual And Installation Instructions Download | Manualshive

Page: 10 / 10

background image

Page | 10

P

800.872.3267

F

800.232.7329

E

techsupport.adamsrite@assaabloy.com

www.adamsrite.com

Installing the Mounting End Caps

1. INSTALL Hinge End Mounting End Cap on hinge

side of door using two (2) #8-32 x 3/8” tri lobe
pan head screws.

2. INSTALL Latch End Mounting End Cap on

latch side of door using two (2) #8-32 x 3/8”
tri lobe pan head screws.

Maintenance

1. CHECK mounting fasteners periodically and TIGHTEN if loose.
2. APPLY screw locking compound or CHANGE part fasteners if screws continue to back out.
3. PERFORM periodic and required checks and adjustments of strikes to compensate for wear and tear

such as door sagging.

Warranty

For complete warranty information, please visit the Adams Rite website:
http://www.adamsrite.com/en/site/adamsritecom/about/warranty/

«
...
8
9
10

Summary of Contents for Adams Rite EX88











Reviews:

No comments

Related manuals for Adams Rite EX88

Brand: Vector Welding Pages: 81

Brand: SanRex Pages: 4

Brand: R-Tech Pages: 20

Brand: Nabco Pages: 32

Brand: H&S AUTOSHOT Pages: 23

Brand: Beninca Pages: 16

Brand: Gretsch-Unitas Pages: 2

TECNICAPLASMA18-31

Brand: Telwin Pages: 20

Brand: Lincoln Electric Pages: 100

Brand: Lincoln Electric Pages: 152

Brand: SWS Pages: 13

SIRIUS 3RV19 6 2 Series

Brand: Siemens Pages: 5

SIRIUS 3RV2926-1B

Brand: Siemens Pages: 8

Brand: Siemens Pages: 8

Brand: Siemens Pages: 7

Brand: Siemens Pages: 23

Brand: Lincar Pages: 64

Brand: BAUKER Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands