Assa Abloy Adams Rite EX88 Preparation Manual And Installation Instructions Download

Page: 5 / 10

Page | 5

800.872.3267

800.232.7329

techsupport.adamsrite@assaabloy.com

www.adamsrite.com

Preparing the Door for Cylinder or Trim

1. PREPARE the exterior and interior of the door for cylinder or trim using the latch end door template

and exterior cylinder template, as required.

2. PREPARE the door for cylinder mounting or trim mounting according to manufacturer’s instructions,

as required.

9/32”

Mounting

Centerline

Bar Height Centerline

Cylinder Centerline

Bar Height

Centerline

Bar Height

Centerline

1/4”

1/8”

13/16”

13/32”

3/8”dia

7/32”dia thru
c’sink 3/8”dia
x 82 deg, 2 plc

(cylinder only)

Exterior Preparation for Use with Cylinder

Interior Preparation for Use with Trim and Cylinder

Bar Height Centerline

Cylinder Centerline

1/8”

1-3/16”dia

(cylinder only)

Summary of Contents for Adams Rite EX88











Search results

Summary of Contents for Adams Rite EX88

Reviews:

Related manuals for Adams Rite EX88

Brands by name

Popular brands

Assa Abloy Adams Rite EX88, Preparation Manual And Installation Instructions

Search results

Summary of Contents for Adams Rite EX88

Reviews:

Related manuals for Adams Rite EX88

Brands by name

Popular brands