Assa Abloy Adams Rite EX88 Preparation Manual And Installation Instructions Download | Manualshive

Page: 8 / 10

background image

Page | 8

P

800.872.3267

F

800.232.7329

E

techsupport.adamsrite@assaabloy.com

www.adamsrite.com

Installing the Strike Plate

1. INSTALL the Strike Plates using two (2) #10-32

x 3/4” flat head screws.

2. VERIFY that exit device is fully operational.
3. ADJUST strike plate as necessary using shim

plates provided.

4. MARK, CENTER PUNCH, DRILL 5/32” diameter

pilot hole for center screw.

5. INSTALL the #10-32 x 3/4” flat head self-

tapping center screw to maintain optimum
adjustment.

10-32 x 3/4"
flat head self-
tapping
screws, 2 qty

10-32 x 3/4"
flat head self-
tapping screw,
1 qty

«
...
6
7
8
9
10
»

Summary of Contents for Adams Rite EX88











Reviews:

No comments

Related manuals for Adams Rite EX88

Brand: Cal-Royal Pages: 4

Brand: Raider Pages: 74

Brand: P.I.T. Pages: 34

Brand: H&S AUTOSHOT Pages: 19

Brand: 2VV Pages: 24

Brand: Danfuss Pages: 12

Brand: Dorex Pages: 2

VRV EMERION REYQ-AATJA

Brand: Daikin Pages: 526

Brand: Westweld Pages: 18

MASTERTIG AC/DC 2000

Brand: Kemppi Pages: 31

Brand: LOTOS Pages: 20

Brand: Comparc Pages: 28

Brand: Jasic Pages: 36

Brand: Unimig Pages: 20

Brand: Tucker Pages: 60

Warrior 500i CC/CV

Brand: ESAB Pages: 84

Brand: RS Pages: 16

Brand: Sargent Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands