background image

 

 

 

Page 2 of 16         For more information visit website assaabloyesh.com         P/N: 3080006.016 Rev1 

                                                                           

 

 

 

 

Recommended Tools 

 

Flathead Drivers — 3/32”, 3/16” 

Drill, Drill Bits — 1/16”, 3/16”, 1/2” 

Phillips Drivers — P0, P2 

Pencil, Wire Stripper, Level, Square, Ruler, Punch, Scissors 

 
Hardware Specifications  

 

Table 1 – Shaft Length 

 

 

 

 

Table 2 – Mounting Screw Length for Various Door Thickness 

Door 

Thickness 

Reader 

Mounting 

Cut to 

approx. 

screw 

length 

Lock 

Mounting 

Cut to 

Approx. 

Screw 

Length 

1/16” 

Coupling Nut 

and 3” Rod 

10/16” 

8-32 x 1-3/4” 

Break Away 

1-1/16” 

1/4" 

Coupling Nut 

and 3” Rod 

13/16” 

8-32 x 1-3/4” 

Break Away 

1-1/4” 

1/2” 

Coupling Nut 

and 3” Rod 

1-1/16” 

8-32 x 1-3/4” 

Break Away 

1-7/16” 

3/4” 

Coupling Nut 

and 3” Rod 

1-5/16” 

8-32 x 1-3/4” 

Break Away 

No Cut 

1” 

Coupling Nut 

and 3” Rod 

1-9/16” 

8-32 x 2-1/2” 

2” 

1-1/4” 

Coupling Nut 

and 3” Rod 

1-13/16” 

8-32 x 2-1/2” 

No Cut 

1-1/2” 

Coupling Nut 

and 3” Rod 

2-1/16” 

8-32 x 2-3/4” 

No Cut 

 

For Technical Support Please call 1-800-810-WIRE 

Door Thickness 

Shaft Used 

1/16” – 1/2” 

L1 

>1/2” – 1½” 

L2 

>1½” – 2¼” 

L3 

Summary of Contents for Aperio Series

















Reviews: