14. TUV is only used in Europe. Set Dipswitch 10 up for all North American applications.
15. Set Dipswitches 11-12 UP. These are the safety/test input and output switches which allow the sensor and
Unislide to communicate (see section 3-7 of manual).
16. Set Dipswitch 13 as desired. Down = Bidirectional function, UP = Unidirectional function (see sect. 3-8 of
manual.
17. Set Dipswitch 14 ON for simultaneous output (see section 3-9 of manual). Exception: On Access Control
ONLY, on the interior or non-restricted access side sensor, set dipswitch 14 OFF.
NOTE: Dipswitch 15 is not used.
18. Slide the FUNCTION KEY switch (6) to OPERATION mode.
19. On the Unislide Control set the Besam Function Selector Dipswitch 7 to ON (up).
Quick Reference
Guide
1. Mount the sensor about 1/8” above the bottom of header. Not
above the bottom of the plank cap.
2. Slide FUNCTION KEY switch (6) to SETTING mode.
3. Slide Dipswitch #16 to ON (see
section 3-9
of manual).
4. Set sensitivity as needed using Dipswitches 1-2, low, middle, high or super high.
�������� ������ �� ������ ��������
��� ����������
������ ����������
���� ����������
��
�
�
�
��
�
�
��
��
�
��� ������
��� ������
��� ������
��� �������
��� �������
������
������
������
������
������
���
���
���
����
����
������
������
������
���� ����� �����
��������
����
������
���
������
����
������
� �
� �
� �
� �
10. Set Presence Detection Timer (learn time) as needed using Dipswitches 3-4.
Select 30 sec., 60sec., 180sec., or infinity (see
section 3-2
of manual).
11. If two or more sensors are mounted near each other and overlap (e.g.,
two single slides sharing the lock jamb) set the frequency different for
each sensor using Dipswitches 5-6 (see
section 3-3
of manual).
12. Select how many sensor rows are to be active using
Dipswitches 7-8 (see
section 3-4
of manual).
13. If door is ghosting set immunity Dipswitch 9 up. Detection pattern may be smaller, check for ANSI
A156.10 compliance and readjust angles and sensitivity if needed.
�� ����
�� ���� ��� ����
� �
� �
� �
� �
∞
������� � ������� � ������� � ������� �
� �
� �
� �
� �
� ����
� �
� ����
� �
� ����
� �
� ����
� �
���
��
�
�
Note: All sensors are sent out adjusted
to maximum settings and will need to
be field adjusted.
1st to 3rd rows
4th and 5th rows
Narrow
Shallow
Deep
Low
Middle
High
S-High
Sens
itivity
15sec.
60sec.
180sec.
Pres
ence
timer
Setting 2
Setting 3
Setting 4
Setting 1
Freq
uenc
y
Row
adjus
tmen
t
5 rows
4 rows
3 rows
2 rows
Width
R
L
Width
R
L
Not
applicable
0
�
35
�
-3
�
3
�
40
�
30
�
5730870
1 2 3 4
6 7 8
9 10
11 12
14
15
16
13
5
Wide
Narrow
Wide
1,2
3,4
5,6
7,8
Depth
-6
�
6
�
Depth
26
�
44
�
Function key
Setting
mode
Operation
mode
Attention
For dipswitch setting,
change it to "Setting
mode".
When setting finished,
set it to "Operation
mode".
Self
mon
itorin
g
Imm
unit
y
ON
OFF
Disable
Enable
9
10
Safe
ty / t
est
outp
ut
Low
High
11
Test
inpu
t
Low
High
12
N.O.
N.C.
14
Act
ivat
ion
out
put
20msec.
10msec.
13
Tes
t in
put
del
ay
Inst
alla
tion
mo
de
16
ON
OFF
6
�
-6
�
26
�
44
�
��� ���� ���������� ����
��� �������� �����
��� ���������
��� ��������� ��������� ��� ����� �����
���������� �����
��� ����� ����������
������
��� �������� ���
��� �����������
��� ���������
������
���
������
��������
SR221-2
SR221-2
5. Using the tool supplied adjust the depth of the threshold zone rows 1-3 by turning the RED RING (4).
6. Adjust the width of the threshold zone rows 1-3 by turning adjustment screws (5 left).
7. Slide Dipswitch 16 to OFF.
8. Adjust the depth of the motion zone rows 4-5 by turning the BLUE RING (4). All rows 1-5 can be adjusted
simultaneously using combo side of tool (
section
1-2 of manual).
9. Adjust the width of the motion zone rows 4-5 by turning adjustment screws (5 right).
Troubleshooting Note: If the operation LED begins flashing Red/Green this indicates a dipswitch was set improperly. To clear this
mode move the function key to Setting Mode, move any dipswitch and then return the function key to Operation mode.
Rev. 5: For Lot Number 1213H and Higher
6
20. On SL-500 control set program parameter 09 (Monitoring) to value 02.
