background image

®

ASSA ABLOY

In U.S.:
Corbin Russwin, Inc.
225 Episcopal Road
Berlin, CT 06037 USA
www.corbinrusswin.com

In Canada:
ASSA ABLOY Door Security Solutions Canada
160 Four Valley Drive
Vaughan, Ontario, Canada L4K4T9
www.assaabloy.ca

Technical Product Support:

  Phone:  888-607-5703

Installation Instructions

FE5400S(A) Series
3 Point Exit Devices

1 of 14

Copyright © 2012 Corbin Russwin Inc., an ASSA ABLOY Group company. 
All rights reserved. Reproduction in whole or in part without the express written 
permission of Corbin Russwin, Inc. is prohibited. 

FM329 (11/18)

Front Cover

Strike

 Top

Chassis

               Top Latch

Outside Trim

Device is packed ready for

any compatible trim.

Bottom Chassis

Bottom Strike

Dogging

Key

Dogging

Feature to hold bolts retracted and

touchpad depressed, for push-pull door

operation.

To Dog Device

1. Insert dogging key.
2. Hold touchbar depressed.
3. Turn key 1/4 turn clockwise.

(Not a feature of fire labeled devices.)

       Top Chassis Cover

      Upper Rod

      Rod Guide

Bottom Chassis

Cover

Lower Rod

      Rod Guide

End Cap

      Bottom Rail

Maintenance

1.

  Periodically remove covers and 

coat mechanisms with a silicone 
base lubricant. This is particularly 
required in corrosive environments 
for proper product function.

2.

  Check mounting fasteners 

periodically. Retighten if found 
loose. Apply screw locking 
compound (available at automotive 
part stores).

3.

  Periodic checks (and adjustments) 

of strikes are required to 
compensate for changes in the 
opening (e.g. door sagging, 
binding, etc...).

NOTE: To meet the certification  
requirements, use fasteners and hardware 
provided with this product. Factory 
supplied fasteners & hardware must be 
used to maintain product certification.

      Touch Bar

End Cover

 WARNING

This product can expose  

you to lead which is  

known to the state of  

California to cause cancer 

and birth defects or other 

reproductive harm. For 

more information go to  

www.P65warnings.ca.gov.

08/2018

Summary of Contents for Corbin Russwin FE5400S Series

















Reviews: