background image

SE LP10 ML20600 Mortise Lock

9

Copyright © 2020, ASSA ABLOY Access and Egress Hardware Group, Inc. All 

rights reserved. Reproduction in whole or in part without the express written 

permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.

6) Wiring Diagrams (Continued)

Typical (UL294-Compliant) SE LP10 Mortise Application Diagram #1

 

Tamper will trigger when reader is removed from door and tamper wiring is connected at the panel. 

SE LP10 

12 Conductor

ElectroLynx Harness

From McKinney

READER NEG - Black, 1

READER POS - Red, 2

DATA 1 - White, 3

DATA 0 - Green, 4

RX (NO) - Orange, 5

RX (COM) - Blue, 6

*EARTH GROUND - Brown, 7

TAMPER - Yellow, 8

LOCK NEG - Violet, 9

LOCK POS - Gray, 10

DPS (NC) - Pink, 11

DPS (COM) - Tan, 12

(-)    

12VDC

(+)

DATA 1

DATA 0

RX (NO)

RX (COM)

Electrical 

Access 

Control 

Panel 

(By Others)

Use (NC) for 

Fail Safe 

Operation

Lock Relay

(NO) Fail 

Secure 

Operation

DPS 

DPS

QC12 Electric 
Hinge From 
McKinney

Panel Circuitry 

Unsupervised Open 
Collector Tamper

  

5VDC

A to D Converter

1K

Ω

1K

Ω

1K

Ω

Input            

Connection (+)

Input           

Connection (

-

)

*IMPORTANT: Pin 7 must be tied to earth ground in the access 

   control panel.

  Wiring in accordance with the NEC, ANSI/NFPA 70 

 

  Fail secure installations are subject to approval of local AHJ

  Fail secure installations shall permit use of Listed panic  

  hardware to allow emergancy exit from the protected area.

  Failure to follow proper ESD safe grounding procedures could 

   lead to equipment failure. 

*UL294 is a United States based standard. 

12V

24V

Average

Peak

Average

Peak

Reader

100mA

220mA

n/a

n/a

Actuator

15mA

500mA

15mA

500mA

12/24VDC System

Power Supply

(By Others)

12-24VDC

H    N    G

120 VAC

Input

Black (Hot)

    White (Neutral)

         Gr

een (Gnd)

12VDC

-      +

-      +

Summary of Contents for Corbin Russwin SE LP10 ML20600





























Reviews: