background image

 

 Copyright, 2001, all rights reserved 

 Securitron Magnalock Corp., 550 Vista Blvd., Sparks NV 89434, USA 

Tel: (775) 355-5625 

 (800) MAGLOCK 

 Fax: (775) 355-5636 

 Website: www.securitron.com 

       An ASSA ABLOY Group company   

 

 

 

 

 

 

 

     

 

PN# 500-18800  

 

 

Page 1 

Rev. A.1, 8/01 

SECURITRON MODEL MUNL-12, MUNL-24 MORTISE UNLATCH 

INSTALLATION AND OPERATING INSTRUCTIONS 

1.  DESCRIPTION 

Securitron’s Mortise UnLatch is a revolutionary new type of electric strike which 

eliminates the 

necessity to perform a routing operation on the door frame for installation

.  The 

motor 

driven

 Mortise UnLatch also presents a 

fully concealed appearance

 on the door which not 

only enhances architectural appeal but 

improves security

 over a conventional electric strike as 

an intruder is less able to determine the type of security device present on the door.  The 
Mortise UnLatch 

functions with all North American mortise locks

 and includes a 

latch 

status output

 which reports when the door is in latched (secure) condition or is open. 

Product Specifications

 

are:  Input Voltages

:  12 VDC (MUNL-12), +20%, -10%.  24 VDC 

(MUNL-24), +20%, -10%.  

Current

:  At rest: 40 mA (either voltage).  When operating- 4 Amp 

input surge @ 12 VDC; 2 Amp input surge @24 VDC for 100 milliseconds and 600 mA @ 12 
VDC or 300 mA @ 24 VDC during motor movement.  

Operating Temperature

:  -10

°

 to 125

°

 F. 

 

FIG 1:  MORTISE UNLATCH DIMENSIONS (INCHES) 

1.25

1.25

1.88

3.50

3.38

RECOMMENDED TOOLS

4.88

SPRINGLATCH
PLUNGER

DEADLATCH
FINGERS

 SMALL PHILLIPS DRIVER
MEDIUM SLOTTED DRIVER
CHISEL, 5/64 ALLEN WRENCH
WIRE CUTTER/STRIPPER
VOLT/OHM METER
CRIMP CONNECTORS
CRIMP PLIERS

 

2.  PHYSICAL INSTALLATION 

2.1  SURVEY 

The installer must first be sure that the 

latch is of the mortise type

 

(see the drawing to the right.)  A mortise lock (or latch) includes a 
square shaped springlatch and a “pin” called the deadlatch pin or 
guard bolt which may be positioned either above or below the 
springlatch. Most 

mortise panic bar

 latches are also perfectly 

compatible with the MUNL.  

Note, however, that if the mortise lock 

assembly includes a dead bolt

, the dead bolt will not be operable  

The most common 

alternate type of latch

 in use in North America is 

called 

cylindrical, tubular or bored

.  The standard UnLatch (model 

numbers UNL-12 and UNL-24) is designed for this alternate type of 
latch. Securitron does not offer an UnLatch solution for a rim latch 
(rim latches are on the surface of the door rather than being mortised 
into the middle of the door).  

Deadlatch Pin

Springlatch

Summary of Contents for Door Lock












Reviews: