background image

Shaft Length

Door Thickness

Shaft Used

1/16" – 1/2"

L1

> 1/2" – 1-1/2"

L2

>1-1/2" – 2-1/4"

L3

Hardware Specifications

Micro USB Port

For emergency power & local 

(hard wired) firmware updates, 

use micro USB port located on 

the side of the K100 reader.

Mounting Screw Length for Various Door Thickness

Door Thickness

Reader Mounting

Cut to Approximate 

Screw Length

Lock Mounting

Cut to Approximate 

Screw Length

1/16"

Coupling Nut & 3" Rod

10/16"

8-32 X 1-3/4" Break Away

1-1/16"

1/4"

Coupling Nut & 3" Rod

13/16"

8-32 X 1-3/4" Break Away

1-1/4"

1/2"

Coupling Nut & 3" Rod

1-1/16"

8-32 X 1-3/4" Break Away

1-7/16"

3/4"

Coupling Nut & 3" Rod

1-5/16"

8-32 X 1-3/4" Break Away

No Cut

1"

Coupling Nut & 3" Rod

1-9/16"

8-32 X 2-1/2"

2"

1-1/4"

Coupling Nut & 3" Rod

1-13/16"

8-32 X 2-1/2"

No Cut

1-1/2"

Coupling Nut & 3" Rod

2-1/16"

8-32 X 2-3/4"

No Cut

Product Specifications

•  Wireless

 

Frequency 

2.4GHz, IEEE 802.15.4, using 

AES 128-bit encryption

•  Lock Battery Type 

AA Lithium, 1.5 Volts (V)

•  Battery Life 

50,000 cycles*

*All battery life claims are approximate and based 

on a set configuration profile. Battery performance 

is based on pre-defined system settings such 

as battery chemistry and battery model used, 

credential presentation settings (LED/buzzer), 

UHF polling period, UHF status intervals, and 

operations per day. Actual battery performance 

will vary and depends on the factors above.

•  Holding Force 

400 lbs

•  Operating

 

Temperature

 

32° to 122° F (0° to 50° C)

•  HID

®

 multiCLASS SE

®

 technology 

Credentials Supported:
•  High Frequency (13.56 MHz):

 

»

HID iCLASS

®

 

»

HID iCLASS SE

®

 (SIO-enabled)

 

»

HID iCLASS

®

 Seos™

 

»

HID MIFARE

®

 SE

 

»

HID DESfire

®

 EV1 SE

 

»

MIFARE CLASSIC

 

»

DESfire

®

 EV1

•  Low Frequency (125 kHz):

 

»

HID Prox

®

, AWID, EM4102, ioProx

•  NFC/BLE*

 

»

Mobile – enabled credentials

*Supported on BLE-enabled models

of 12

Summary of Contents for HES Aperio K100













Reviews: