86
FR
Fonctions et utilisation
Verrouillage automatique
La
serrure multipoints motorisée 519N
se verrouille automatiquement. Sur
une serrure de porte avec verrouillage automatique, la porte fermée est
toujours verrouillée.
Principe de fonctionnement
La
serrure multipoints motorisée 519N
est équipée d’un contact de porte
(Fig. 4 –
1
et « Explication de la terminologie employée », page 84) qui
est repoussé par la têtière lorsque la porte se ferme.
Lors de la fermeture de la porte, le pêne demi-tour (Fig. 4 –
3
)) en position
sortie est repoussé vers l’intérieur au contact de la têtière (côté dormant).
Lorsque le pêne demi-tour est repoussé, le pêne pilote (–
2
) est lui aussi
repoussé. Lorsque la porte est entièrement fermée, le pêne demi-tour
ressort en pénétrant dans l’ouverture de forme prévue de la têtière (côté
dormant), tandis que le pêne pilote reste enfoncé.
Au moment où le pêne demi-tour est sorti et que le pêne pilote est en
même temps enfoncé, le pêne dormant (–
4
) est libéré et sort, grâce à un
mécanisme par ressort. Lors de l’utilisation courante, ce mécanisme
empêche la sortie du pêne dormant lorsque la porte est ouverte.
Le processus de verrouillage est seulement terminé lorsque le pêne demi-
tour et les pênes dormants sont sortis et que le contact de porte est activé.
La serrure est verrouillée.
Contact de porte
Le contact de porte est activé par la têtière et indique l’état de la porte.
En cas d’utilisation du module IO N5950 OneSystem
Si la
serrure multipoints motorisée 519N
est connectée au
module IO N5950 OneSystem
, alors le signal de
sortie du contact de porte est traité. Une signalisation d’état
« porte fermée » est émise.
Signalisation d’erreur
Si le pêne demi-tour est sorti et que le pêne pilote est en même temps enfoncé sans que le contact de
porte n’ait été actionné par la têtière, une erreur s’est produite (« La serrure ne verrouille pas », page 109).
L’automatisme suivant se déroule :
· La serrure verrouille de manière mécanique (« autoverrouillage ») et déverrouille de manière motorisée.
- Un message d’erreur pouvant être affiché via le
module IO N5950 OneSystem
est généré
.
· Le message d’erreur est acquitté automatiquement lorsque les pênes dormants sont reverrouillés par
un actionnement motorisé ou mécanique.
La cause du problème doit être éliminée.
Fig. 4 :
1
Contact
de
porte
2
Pêne
pilote
3
Pêne demi-tour
4
Pêne dormant
1
2
3
4
Fonctions et utilisation
Summary of Contents for OneSystem 519N
