Pando
™
Mini Go reader
IS559883940PA1
Configuration of system keys
(
Only the first time a reader is taken into use
)
Read the whole instruction before you start with the configuration.
1)
Power off and on the reader
2)
Orange and red indication flashes for 10 seconds
3)
Display the Key Setup Card for the reader before it stops
flashing
4)
Keep the card on the reader for at least 15-20 seconds
The reader will beep with two beeps per second (2Hz)
5)
When! The reader indicates with a "chirp" the programming
of the keys is complete
Key setup card
NOTE! If a mobile phone presented for a Pando BLE reader does not
have encryption keys that match those in the reader, it will not send
any data.
Mobile phone modes
There are four different modes from the mobile phone that you can
customize for the reader to accept.
Tap: Which means that you touch the BLE reader with the phone in
the same way as a card
* Twist and Go: You turn the phone from side to side to activate the
BLE reader closest to you.
* Seamless: The phone activates the readers closest to you without
having to touch the mobile phone itself. In this mode, DIP function 3
can be recommended if there are several BLE readers close to each
other.
Notification: Enable the BLE reader via smart watch. The mobile
phone must be within reach of both clock and readers.
* Functions ”Twist and Go” & ”Seamless” must also be enabled in
the Mobile Access application.
Technical documentation and support
We reserve the right to correct printing errors and update the information after printing.
At the website (
https://teknisksupport.assa.se/
) technical support can you find detailed
manuals available for the ARX access control system. If you cannot find answers to your
questions in the manuals, we refer to the technical support in your country
Enable and disable features and adjust
readers accepted reading distance
For each function / mobile phone mode, you can set whether the
function should be active or not and adjust the distance you want
between the mobile phone and the reader. This is done by using
the configuration card
.
During the first 10 seconds after power on, you can adjust the
function and distance of the Pando BLE reader. After displaying a
configuration card within the first 10 seconds, you have 30
seconds to display the card again or switch to a new
configuration card.
For example, to adjust the "Seamless" reading distance, select the
configuration card labeled
"BLE Seamless Configuration Card".
Restart the reader and view the card for the Pando BLE reader.
Each time the card is displayed to the reader the reader will beep
1-6 times and the distance changes. The different functions have
different numbers of step.
1 beep = function off
2 beeps = shortest accepted reading distance, 6 beeps = longest
accepted reading distance.
See the configuration card manual for detailed information of each
card function and values.
The QR code on the back of the card is a link to the configuration card
information sheet.
Try with a mobile phone that belongs to the system if the correct
distance and function has been achieved for each function.
The configuration cards are not system-bound and can be used on
different systems.
The configuration cards for the different reading methods and
reading distances are ordered separately. All types of configuration
cards are included.
Part No: S559688990
When the BLE reader is configured, the distance from the current Pando BLE reader to the next Pando BLE reader must be taken into account to get
the desired function and the correct door activated by the mobile phone. Select function and distance according to the current conditions.
Keep in mind that the range of the bluetooth signal may be significantly reduced when using mobile phone cases. If not the sufficient length is
achieved remove the case.
The Bluetooth range may also vary between different mobile phone manufacturers and models.
Default values in the reader upon delivery
(
Variations between different mobile phone brands may occur
)
Function
Approx. Reading distance
Tap
5 -10 cm
Twist & Go
1,5-2 m
Seamless
1,5-2 m
Notification (Via smart watch)
1,5-2 m
Advertise DIP3 = ON
Normal mode 2
The "Notification" features via smart watch does not work without the phone being within reach of both clock and readers.
Message in App "No reader in range" or
"Twist and Go not supported by reader". See the configuration card manual, scan the QR code with the mobile.
QR Mobil User Guide