background image

800-810-WIRE (9473) • www.sargentlock.com

 

• 

A7757C

Profile Series v.G1 Exit Device

Copyright © 2006, 2008, Sargent Manufacturing Company

, an A

SSA ABL

O

Y Group company

. All rights reserved. 

Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

Table of Contents

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced TV technician for help

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme avec la norme NMB-003 du Canada.

Warning

1

Warning: Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.

Warning

General Description ...........................................................................1

Specifications ....................................................................................1

Features .............................................................................................1

Parts Breakdown .............................................................................2-5

Installation Instructions–Rim Type Device .....................................6-9

Installation Instructions–Mortise Type Device  ............................10-13

Operational Check ............................................................................14

Installation of the RF Technology Lock (G1-TU, G1-TA, G1-TP)......14

1

2

3

4

5

6

7

Page

8

Warning

!

To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.

9

Summary of Contents for v.G1 Sargent

















Reviews: