background image

28

P/N YRL-LKFTSINSTL-FUL Rev A

Product Support Tel 1-855-213-5841 • www.yalehome.com

Cet appareillage numérique de la classe A répond à toutes les exigences de l'interférence canadienne causant des règlements d'équipement. 

Equipment Regulations. 

This Class A digital apparatus meets all requirements of the Canadian Interference Causing

Industry Canada:

Class B Equipment 

Ÿ

 Increase the separation between the equipment and receiver.

Ÿ

 Consult the dealer or an experienced radio/TV technician for help.

FCC:

This equipment has been tested and found to comply with the limits for a Class B digital

Ÿ

 Reorient or relocate the receiving antenna.

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with 
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful Interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Ÿ

 Connect the equipment into an outlet on a circuit different from that to which the  receiver is connected.

Warning: 

Changes or modifications to this device, not expressly approved by 

ASSA ABLOY Residential Group, Inc.

 could void the 

user's authority to operate the equipment.

Yale® and Yale Real Living® are registered trademarks of ASSA ABLOY Residential Group, Inc.  

Assure Lever™ is a trademark of ASSA ABLOY Residential Group, Inc. 

Other products' brand names may be trademarks or registered trademarks of their respective 

owners and are mentioned for reference purposes only. 

© Copyright 2019. All rights reserved. Reproduction in whole or in part without the express written 

permission of ASSA ABLOY Residential Group, Inc. is prohibited.

Summary of Contents for Yale Real Living Assure Lever YRL256

































Reviews: