ASSEMBLY
Introduction
• The Assault Fitness AirRunner treadmill requires only minor assembly. All tools required to complete the initial
setup and assembly have been included in the Assembly Hardware Kit.
• Remove the unit and all parts from the carton and packaging. Confirm all parts shown in the section titles
As
Shipped
are included before attempting assembly of the AirRunner.
Assembly Step One: Upright Installation
• Locate the
Speed Sensor Cable – Lower (549a)
and ensure the end/connector is extending from the main
frame.
• Raise the
Upright – Left
vertically, ensuring the
Keyholes
are located at the bottom. Align the
Upright - Left
keyholes with the two posts located on the main frame. This will support the upright while completing the
installation.
• Connect the
Speed Sensor – Lower (549a)
and
Speed Sensor Cable – Middle (560b)
connectors firmly.
• Locate three (3) sets of
#534 Hex Screws
and
#562 Flat Washers
, and loosely thread each assembly through the
Left Upright
and into the main frame. Tighten the screws firmly.
• Hang the
Upright – Right
keyholes onto the
Main Frame
posts and install the remaining three (3) sets of
#534
Hex Screws
and
#562 Flat Washers
.
6
Console (514)
Console Cover
- Right Inner (530)
Console Cover
- Right Outer (531)
Upright - Left
(502)
Upright
- Right (503)
Sidecase Center Cover
- Right (510)
Sidecase Center Cover
- Left (507)
Main Assembly (A)
Console Cover
- Left Inner (529)
Console Cover
- Left Outer
(528)
Handrail (504)
Speed Sensor Cable - Upper (559a)
Speed Sensor
Cable
- Middle (560a)
Speed Sensor
Cable - Middle
(560b)
Speed Sensor
Cable - Upper (559b)
Speed Sensor
Cable - Lower (560a)
Console Cable
(514a)
ASSEMBLY TOOLS
AA Alkaine
Batteries
4 pieces
4mm
Hex Wrench
5mm
Hex Wrench
13/16mm
Open-Ended
Wrench
Button Head Hex Screw M8 x 20mm (535)
Hex Screw M10 x 75mm (534)
HARDWARE DESCRIPTION
DRAWING QUANTITY
Flat Washer Ø20OD x 11ID x 1.5t (562)
Phillips Head Screw M4.2 x 13mm (538)
6
6
12
AS SHIPPED
MANUAL TREADMILL
QUICK START
GUIDE
534
562
560b
560(a)
562 534
549a
Upright - Left
Upright - Right
Keyholes
Posts
507
537
537
537
510
537
Upright
Assembly Step Two: Sidecase Covers
• Locate the
Sidecase Center Cover - Left (507)
. Align the tabs locate at the top with the receivers on the installed
sidecase plastics. To install, the cover will hinge downward and snap in place. Ensure the outer surface of the cover
is flush or aligned with the adjacent plastics.
• Secure with two (2)
#537 Phillips Head Screws
.
• Remove the four (4)
#564 Hex Screws
from the backside of the
Console (514)
and set them aside.
• Connect the
Console Cable (514a)
and
Speed Sensor Cable – Upper (559b)
connectors and carefully tuck the excess
cable into the Handrail.
• Loosely thread the four (4)
#564 Hex
Screws
through the mounting plate on
the
Handrail
and into the backside of the
Console (514)
. When all four (4) screws
are installed, tighten firmly.
• With the help of a second person, support
the
Handrail
assembly above the uprights
and connect the S
peed Sensor Cable –
Upper (559b)
and
Speed Sensor Cable –
Middle (560a)
connectors. Carefully tuck
the connectors and excess cables into the
left
Upright
.
• Set the left and right
Handrail
brackets
inside the left and right
Uprights
. While
supporting the
Handrail Assembly
,
loosely thread three (3)
#535 Button
Head Hex Screws
through the left
Upright
and into the
Handrail
bracket.
Assembly Step Four – Final Adjustments
• Identify a suitable location that is level and offers enough space for the unit with the minimum required free
space. It is recommended that the AirRunner be sited with a minimum of 0.5 meters (19.7 in.) of clearance from
the nearest walls or other equipment to the left, right and front of the unit. A minimum of 2.0m (79”) of clearance
should be maintained to the rear of the AirRunner.
CAUTION: THIS TREADMILL IS HEAVY. INJURY CAN OCCUR IF PROPER LIFTING TECHNIQUES
ARE NOT PRACTICED.
• To relocate, raise the rear of the unit with by grasping the transport handle and slowly rolling the AirRunner to
the desired location.
• Ensure the unit is level and does not rock by adjusting the Stabilizer Leveling Feet. Two feet are located at the rear
of the main frame. As a starting point, loosen each foot by threading the assembly downward/clockwise, and
then thread the locknuts downward (clockwise) against the base of the foot. Check the unit for stability and make
any adjustments as necessary. Once stable, lock the Stabilizer Leveling Feet in place by tightening the jamb nut
upward/counter-clockwise, against the underside of the frame to lock the current positions for each foot.
• Congratulations. The assembly of your Assault Fitness AirRunner treadmill is complete. Please read all included
information, user guides and warnings before use.
Assembly Step Three – Handrail & Console Installation
Repeat this step for the right side and tighten all six (6) screws firmly.
• Align the
Console Cover – Left Outer (528)
with the outside of left
Handrail
bracket, and thread two (2)
#537
Phillips Head Screws
through the handrail bracket and into the
#528 Cover
. Repeat this step for the right side
with
Console Cover – Right Outer (531)
.
• Align the
Console Cover – Left Inner (529)
with the inside of the left
Handrail
bracket install two (2)
#537
Phillips Head Screws
through the
#529 Cover
and into the
#528 Cover
.
• Align the
Console Cover – Right Inner (530)
with the inside of the right
Handrail
bracket and install two (2)
#537 Phillips Head Screws
through the
#530 Cover
and into the
#531 Cove
r.
5803 Newton Drive Carlsbad, California 92008 Ph. 1.888.815.5559
For more information or questions regarding your equipment, please visit our website at
AssaultFitnessProducts.com
© Assault Fitness 2017
514a
514
Handrail (504)
535
535
535
535
535
535
Upright
528
560a
559b
537
529
530
531
537
564
504 559b
Stabilizer
Leveling
Foot
Part #23-AS-566 US-English v1.0 05-Mar-17
