Architect's and Engineers' Specification
The microphone shall be an ASTATIC 930VP. The microphone shall be a miniature dual
electret boundary microphone. The frequency response will be 40Hz - 15KHz. The
microphone shall have a continuously adjustable polar pattern.
The output level of the 930VP shall be -32dBV (25mV) @ 1Pa. The microphone will have a
miniature 3 pin connector and be supplied with a 30 foot cable that has a mating connector
on one end and a professional 3 pin XLR type connector on the other end. The microphone
shall have a switch selectable high pass filter with -3dB at 80 Hz and slope of 12dB per
octave when enabled. The microphone shall have a locally controlled mute that will provide
greater than 60dB of attenuation when enabled. The mute shall be configurable for normally
muted / momentary push-to-talk, normally on / momentary push-to-mute or latch on / latch
off operation. When configured for latch on / latch off operation, the microphone shall be
configurable to either power up on or power up off. The microphone shall have a red LED
that will indicate if the microphone is on or off. The microphone will operate from
standard 48V phantom power with a current consumption of less than 6 mA.
The dimensions of the microphone shall be 5 1/2" long, 3 1/2" wide, and 15/16" high. The
weight shall be 4.6 oz not including the cable. The microphone will have a durable urethane
painted finish. The microphone will be black with a black cable or white with a white
cable.
The ASTATIC Model 930VP is specified.
Specifications:
Type:
Electret Condenser Microphone
Polar Pattern:
Cardioid / Omni-Directional / Figure 8, Continuously Variable
Frequency Response:
40Hz - 15KHz
Sensitivity:
-32dBV (25mV) @ 1Pa
Rated Impedance:
330 ohms
Equivalent Noise Level:
<26dB-A
Maximum SPL:
118dB
Signal To Noise Ratio:
>68dB
Power Supply:
48V phantom
Current Consumption:
6mA
Connector:
Mini XLR
External Size:
5 1/2 (140mm) x 3 1/2 (89mm) x 15/16 (24mm)
Weight:
180g
SPECIFICATIONS FOR 930VP
5K
RESPONSE IN dB
-20
10
-30
0
-10
+10
50
100
1K
FREQUENCY IN HERTZ
500
10K
20K
Hi-Pass
Cardioid
5K
RESPONSE IN dB
-20
10
-30
0
-10
+10
50
100
1K
FREQUENCY IN HERTZ
500
10K
20K
Figure 8
5K
RESPONSE IN dB
-20
10
-30
0
-10
+10
50
100
1K
FREQUENCY IN HERTZ
500
10K
20K
Omnidirectional
1KHz
100Hz
0
120
90
60
-5
150
180
150
30
-20
-10
-15
-25
30
90
120
60
Cardioid
0
120
90
60
-5
150
180
150
30
-20
-10
-15
-25
30
90
120
60
1KHz
500Hz
100Hz
Omnidirectional
TWO-YEAR LIMITED WARRANTY
ASTATIC Microphones are warrantied for two years to the original purchaser from the date of purchase by Omnitronics, LLC to be free from defects
in material and workmanship. In event of such defect, product will be repaired or replaced at Omnitronics, LLC discretion with a new unit of equal
or superior value. This will be at no charge if delivered prepaid to Omnitronics, LLC, together with the proof of purchase and a Return Authorization
number. The unit will be returned promptly prepaid. Warranty excludes exterior finish, appearance items, or malfunction due to abuse or operation
under other than specified conditions. Consequential or incidental damages are excluded.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Some states do not allow the exclusion
or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusions and limitations
may not apply to you.
Note: No other warranty, written or oral is authorized by Omnitronics, LLC.
SHIPPING INSTRUCTIONS
Please call our customer service department at 440-593-1111 for a pre-approved return authorization number and carefully repack the unit and return
it to: Omnitronics, LLC, 341 Harbor St., Conneaut, OH 44030
ALL RETURNS MUST HAVE A PRE-APPROVED RETURN AUTHORIZATION NUMBER OR IT WILL BE REFUSED.
If outside the United States, contact your dealer or distributor for warranty details.
46873-23-00 / Rev.2 / 3/3/05 / S.L.W.
Figure 8
