Specifications
†
Operating Principle
............................................Condenser
Polar Pattern
......................................Continuously-variable
Frequency Response
....................................80 Hz - 18 KHz
Sensitivity
..........................................-36dBV (16mV) @ 1Pa
Impedance
............................................................120 ohms
Self Noise
..................................................................29 dBA
Maximum SPL
..........................................120 dB, 1% THD
Power Requirements
..........................P12, P24, P48, 4 mA
Connector
..............................................3-pin male XLR type
Polarity
................................Positive pressure on diaphragm
corresponds to positive voltage
on pin 2 relative to pin 3.
Finish
......................................Durable matte-black urethane
RF Immunity
........................Meets or exceeds EN55103-2,
E1, E2, E3 and E4
RoHS Compliant
†
Specifications subject to change without notice.
Optional Accessories
GSM-1
..............................................................Shock mount
FM-1A
................Flange with 3-pin female XLR stem mount
Architects’ and Engineers’ Specification
The microphone will be a mini-gooseneck condenser type.
The frequency response will be 80-18kHz. The microphone
will have a continuously-variable polar pattern.
The sensitivity of the microphone will be -36 dBV (16mv)
@ 1 Pa. The microphone will have a professional 3-pin male
XLR connector that also contains the electronic circuitry,
variable pattern control and LED on/off switch. A blue LED
light will show through the XLR housing and illuminate
when phantom power is applied. The microphone will
operate from P12, P24 or P48 standard phantom power
consuming 4mA.
The microphone element and electronics will be enclosed
in a radio frequency resistant housing meeting or exceeding
specification EN55103-2. The dimensions of the microphone
will be 1/2" [12mm] in diameter for the head and 1 5/32"
[29mm] in diameter for the connector. The upper gooseneck
will be 1/4" [6mm] in diameter. The lower gooseneck will
be 19/32" [8mm] in diameter. The GN10VP will have a single
1/4" [6mm] diameter gooseneck. The overall height will be
10 1/4" [260mm] for the GN10VP, 15 1/4" [387mm] for the
GN15VP, and 20 1/4" [514mm] for the GN20VP. The
GN10VP, GN15VP, GN20VP will have a durable matte-black
urethane finish. A foam windscreen, locking flange mount
and shock mount will be supplied as accessories.
The
Astatic
model GN10VP, GN15VP or GN20VP is specified.
Omnidirectional
Cardioid
Figure-of-eight
Pattern/LED Adjustment
1.
Disconnect power from microphone.
2.
Straighten the gooseneck.
3.
Remove cover screw using a #1 Phillips screwdriver.
4.
Lift Cover.
5.
Adjust dial to desired polar pattern using a 3/32" (2.5mm) flat-head
screwdriver.
6.
Set LED switch as desired.
7.
Lower cover.
8.
Replace and tighten cover screw.
Dimensional Drawings
(not shown actual size)
Astatic Commercial Audio Products
6573 Cochran Rd. Building
I
Solon, Ohio 44139 U.S.A.
Tel: (440) 349-4900 Fax: (440) 248-4902 Sales: (800) 421-3161
www.astaticinstalled.com
GN10VP/GN15VP/GN20VP
Continuously-variable Pattern Condenser Mini-gooseneck Microphone with Power LED
2 of 4
3 of 4
Sold by:
http://www.TWAcomm.com
Toll Free: (877)
389-0000
