background image

 

                         

Aston

®

 Tire Changer ATC-5733 User’s Manual

 

17 

www.astontechusa.com 

of the machine is consistent. 

 

The machine is connected to the circuit, the circuit must be fitted with a fuse that is in 
line  with  the  operating  rules. The  automatic  circuit  breaker  of  25A  is  required  to  be 
operated by professional personnel. The power plug of the tire changer is provided with 
the customer. 

 

The compressed air system is connected to the machine by a pipe joint on the right side 
of the tank. 

3.5.2 Debugging 

 

Step 1: turn on the power and gas supply, depress the Turntable Rotation pedal, turntable 
should be clockwise. Raise the Turntable Rotation pedal, the turntable should be anti-
clockwise rotation. (If the turntable is opposite to the specified rotation direction, the 
position of the two lines in the three-phase plug should exchange position.) 

 

The second step: depress the Bead Breaker Pedal, start the Bead Breaker device; when 
the pedal is released, the Bead Breaker device to return to the original position. 

 

The third step: depress the Jaw Clamp Pedal, open the 4 clamps; release the Jaw Clamp 
Pedal, the Jaw Clamps returns to the original position.   

Operation declaration 

4.1 Operating notes 

 

Check  the  connection  of  air  pipe  is  in  place,  ensure  that  no  air  leakage,  ensure  the 
operation space to meet the requirements, then start work. 

 

Before any operation, the gas in the tire is needed to be released, and the balance block 
of the tire balancing device is removed.

 

4.2 Disassemble operation process 

4.2.1 Bead Loosening 

 

Deflate  tire  completely  by  removing  the  valve  core  from  the  valve  stem.  To  avoid 
damaging the clamps and/or wheel, move the clamps to their full inward position before 

Summary of Contents for ATC-5733









































Reviews: