background image

THIS WARRANTY DOES NOT COVER: 

1.  Product installed in buildings other than single family dwelling units. 

2.  Product installed outdoors or any other non-standard bathroom location. 

3. Component parts not manufactured by Aston Global. 

4. Workmanship of any installer of Aston Global Product. This warranty does not assume 

any liability of any nature for unsatisfactory performance caused by improper installation, 

or any damages to property resulting from improper installation or use of the Products, 

including but not limited to flooring, subfloor, tile, walls, sheet rock, concrete board, paint, 

plumbing fixtures and ceilings. 

5.  Labor costs incurred in the removal, disassembly, reassembly, or installation of the 

Product(s), including replacement  Products issued under the Warranty, or costs for 

transportation to Aston Global, and any other materials necessary to return Product to 

Aston Global. 

6. Any Product that has been damaged as a result of being improperly serviced or 

operated, including, but not limited to, the following: operated with insufficient water; 

allowed to freeze; subjected to flood conditions; operated with water conditions or 

additives which cause unusual deposits or corrosion in or on the Product, or subject to 

any other abuse or negligence. 

7. Any Product that has been damaged as a result of natural disasters, including, but not 

limited to, lightning, fire, earthquake, hurricanes, tornadoes or floods. 

8.  Product used for any purpose other than residential bathroom usage. 

LEGAL DISCLAIMERS 

ALL IMPLIED WARRANTIES,  INCLUDING WARRANTIES OF MERCHANTABILITY 

AND FITNESS  FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED IN 

THEIR ENTIRETY WITH RESPECT TO ALL PURCHASERS OR OWNERS.  FAILURE 

TO RETURN THE WARRANTY CARD SHALL HAVE NO EFFECT ON THE 

DISCLAIMER OF THESE IMPLIED WARRANTIES. ALL EXPRESS WARRANTIES 

SHALL BE LIMITED TO THE DURATION OF THIS EXPRESS  LIMITED WARRANTY 

AND EXCLUDE ANY LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES 

RESULTING FROM THE BREACH OF ANY EXPRESS WARRANTY. Some states do 

not allow the exclusion or limitation of incidental or consequential damages, so the above 

limitations or exclusions may not apply.  No dealer, distributor, service company or other 

party is authorized to change, modify or extend the terms of this warranty in any manner 

whatsoever. 

Aston Global and it representatives shall not be liable for any injury, loss, cost or other 

damages, whether incidental or consequential, arising out of any defect covered by this 

Warranty including and without limitation, loss of use of the Product and cost for removal 

of defective Product, even if Aston Global has been advised of the possibility of such 

damage.  The liability of Aston Global under this Warranty, if any, shall not exceed the 

original amount paid for the Product covered by the Warranty.  Coverage under this 

Warranty shall commence as of the original date of purchase and the duration of such 

coverage shall not extend for any reason whatsoever beyond the stated time period.  The 

22 

Summary of Contents for Langham SDR978




























Reviews: