Astralpool LUMIPLUS PAR56 RGB 1.11, Installation And Maintenance Manual

3

ENGLISH

IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be 

implemented for installation and start-up. Therefore, the installer as well as the user must read the instructions 

before beginning installation and start-up.

Keep this manual for future reference.

To achieve optimum performance of the LumiPlus PAR56 RGB 1.11 Wireless Lamp, follow the instructions provided 

below:

1. VERIFY THE CONTENTS OF THE PACKING:

59124

59126

59127

1 PAR56 RGB 1.11 Wireless Lamp 
Installation and maintenance manual
Bag of fastenings
Warranty booklet

1 PAR56 RGB 1.11 Wireless Lamp 
+1 LumiPlus Control Motion
Installation and maintenance manual
Bag of fastenings
Warranty booklet

2 PAR56 RGB 1.11 Wireless Lamps
 + 1 LumiPlus Control Motion
Installation and maintenance manual
2 Bags of fastenings
Warranty booklet

2. GENERAL CHARACTERISTICS:

This lamp has been designed to be used fully submerged in fresh water. It is a Class III electric apparatus with very 

low safety voltage 

(12 V with alternating current)

. The lamp is class 116, in accordance with standard EN 50065.

The floodlamp complies with IPX8 degree of protection at a nominal immersion depth of 2 m. 

This floodlamp complies with international safety standards for lights, especially the EN 60598-2-18 standard: LIGHTS 

PART 2: SPECIFIC REQUIREMENTS SECTION 18 LIGHTS FOR SWIMMING POOLS AND SIMILAR APPLICATIONS.

LumiPlus Control Motion must not be washed or immersed in water.

The manufacturer is not responsible in any circumstances for assembly, installation or start-up of any electric compo-

nents which have been inserted or handled at locations other than its own premises.

3. INSTALLATION PAR56 RGB 1.11 WIRELESS LAMP:

s4OCORRECTLYLIGHTASWIMMINGPOOLWERECOMMENDINSTALLALAMPINTHERANGE,UMI0LUSEVERYM£OFWATER

surface.  Recommendation  valid  for  light  coloured  pools.  In  darker  coloured  pools  we  recommend  oversizing  the 

PROPORTIONOFLAMPSPERM£

s4HECONNECTIONBOXESSHOULDBEATLEASTMFROMTHEEDGEOFTHESWIMMINGPOOLORWATERINSTALLATION

s4HE6TRANSFORMERSUPPLYINGTHELAMPSHOULDBEINSTALLEDMFROMTHEEDGEOFTHESWIMMINGPOOLOR

water installation.

s#ONDUITSINSTALLEDLESSTHANMFROMTHESWIMMINGPOOLEDGESHOULDNOTBELINEDORCOVEREDINMETAL

4. ASSEMBLY: 

To remove the projector to the edge of the swimming pool (Fig. 1) loosen the two screws of the decorative ring until the 

FIXATIONSYSTEMFASTENINGDOGYIELDSSUFFICIENTLYSOTHATTHEPROJECTORUNITCANBESEPARATEDFROMTHEHOUSING

1.

 Ensure that the lamp is NOT receiving voltage.

2. 

5NSCREWTHENUTSTHATlXTHETRIMRINGATTHEBOTTOMOFTHEPROJECTOR&IG

Unscrew the two cap nuts (Z), and completely unscrew the two screws (X), see Fig. 3.

%XTRACTTHELAMPFROMTHEINSIDEOFTHEBOTTOMPROJECTORANDDISCONNECTTHETERMINALSLOOSENINGTHETWOSCREWSTHAT

lXTHEMTOTHELAMP&IG

3. 

Change the lamp and assemble the Projector, in the opposite order described, taking special care to:

s#ONNECTTHECABLETERMINALSTOTHELAMPUSINGTHESCREWSSUPPLIEDWITHTHELAMP&IG

s

Fully centre the O-ring in its seat.

s&IRMLYTIGHTENTHENUTS-AXIMUMTORQUE.M

It is essential that the direction of the lamp is adequate, situating “TOP” on the top part of the projector.

5. MAINTENANCE PAR 56 RGB 1.11 WIRELESS LAMP:

4HISLAMPDOESNOTREQUIREANYTYPEOFMAINTENANCEWORK)FYOUNOTICETHATTHELAMPISNOTWORKINGPROPERLYPLEASE

contact our customer attention service.

THIS LAMP DOES NOT CONTAIN ANY ELEMENTS THAT CAN BE HANDLED, DISMANTLED OR REPLACED BY THE 

USER.  IT IS FORBIDDEN TO ACCESS INSIDE THE PRODUCT, OTHERWISE THE GUARANTEE OF THE PRODUCT 

WILL BECOME INVALID.