5
4HEBUTTONSENABLEYOUTOSELECTONEOFTHEEIGHTSEQUENCESORDEREDFROMTHESLOWESTTOTHEFASTESTSPEED
- Switching spotlights off
4HESPOTLIGHTSARETURNEDOFFBYPRESSINGTHE/./&&BUTTON4HESTATUSCOLOURSEQUENCE OFTHELAMPSISSTOREDINTHE
MEMORYFORTHENEXTTIMETHESYSTEMISSWITCHEDON
- Switching the remote control off
The remote control automatically switches off in less than 60 seconds.
The LED display lights on the remote control only light up for a few seconds.
7.2 Control motion mode
(see page 28)
7HENTHECONTROLMOTIONMODEISSWITCHEDONTHECOLOURSANDSEQUENCESCANBECHANGED
Changing the colour (Fig. A)
- Hold the remote control firmly without touching any of the buttons.
- Flick your wrist downwards.
- The change in colour will be displayed on the Central Display.
#HANGINGTHESEQUENCE
(Fig. B)
- Hold the remote control firmly without touching any of the buttons.
- Flick you wrist form side to side.
4HECHANGEINSEQUENCEWILLBEDISPLAYEDONTHE#ENTRAL$ISPLAY
8. CONTROL MOTION MAINTENANCE:
If the Central Display lights up in red without switching off, this means the batteries are low. The battery case is on the
BACKOFTHE#ONTROL-OTIONUNITREPLACETHEOLDBATTERIESWITHTWONEW!!!6ONES
9. WIRING:
Diagram of the wiring (see page 28)
In order to wire the system properly, a lamp, transformer and the Control Motion unit will be needed.
4HETRANSFORMERSHOULDBECONNECTEDTOA6^ACPOWERSUPPLYANDTHELAMP6^AC TOTHEAUXILIARYWINDING
)TMUSTBESIZEDTOSUPPLYTHECORRESPONDING6!TOEACH,%$LAMPTHATISWIREDSEETABLEONTHEBACKCOVER &OR
EXAMPLEIFYOUWISHTOCONTROLTWO6!0!2LAMPSTHEYMUSTBEWIREDINPARALLELTOTHETRANSFORMERTOAT
LEAST6!
!LTERNATIVELYTHESYSTEMCANBECONTROLLEDUSINGASIMPLE.#PUSHBUTTONINWHICHCASETHEREWILLBEFUNCTION
MODESSEVENSETCOLOURSANDSEVENDIFFERENTCOLOURSEQUENCES%ACHTIMETHEPUSHBUTTONISPRESSEDTHECOLOUROR
SEQUENCEWILLCHANGE"YPRESSINGFORSEVERALSECONDSTHELIGHTBECOMESWHITE
10. TROUBLESHOOTING:
Problems
Usual causes
Solutions
The lamp is not working
The lamp does not have a power supply
Connect the lamp to the power
SUPPLYTHROUGHA6^ACSAFETY
transformer.
The lamp projects a different colour
to that shown on the Control Motion
Central Display
4HELAMPSDONOTRECEIVEINFORMATION
1. Get close to the lamp before
sending a command
2. Do not cover the antenna with
your hand
3. Press the REFRESH button
Two lamps project different colours
Using the control motion mode, the
lamp does not work
Control Motion is not responding
The Control Motion batteries are low
Change the batteries
11. SAFETY WARNINGS:
s!VOIDMAKINGCONTACTWITHTHEELECTRICVOLTAGE
s#OMPLYWITHTHECURRENTSTANDARDSREGARDINGACCIDENTPREVENTION
s)NTHISREGARDTHE)%#STANDARDSMUSTBEOBSERVED7)2).')."5),$).'330%#)!,7)2).'37)-
-
MING POOLS.
s4HISLAMPISSUITABLEFORUSEINSEAWATERUNLESSPROJECTORSPECIlCATIONSSTATEOTHERWISE
s!LLMAINTENANCEOPERATIONSSHOULDBEPERFORMEDWITHTHELAMPDISCONNECTEDFROMTHE-AINS
s$ONOTHANDLEWITHWETFEET
Summary of Contents for LUMIPLUS PAR56 RGB 1.11
Page 2: ...2...
Page 27: ...27 2500mm 400 700 mm FIG 1 FIG 4 FIG 3 Z X FIG 2...
Page 30: ...30 s 3 3 s 3 3 s 3 3 s 3 s 335 s 3 3 50 6 186 22 177 102 28 170...
Page 31: ...31...
