background image

15

QB800 robotic cleaner   

Owner’s Manual

14

QB800 robotic cleaner   

Owner’s Manual

Message

Possible Cause

Solution

The cleaner is not climbing 

walls.

The filter canister is full or dirty.

Dispose of debris and thoroughly clean the filter canister 

with mild soap and a soft brush. Then, re-submerge the 

cleaner (see: 

Clean the Filter Canister

).

Tyre treads worn down.

See: 

Replacing Wear Parts.

Confirm appropriate pool  

chemistry.

Speak with your pool service professional.  

Do not leave cleaner in the pool during any chemical 

treatments.

The cleaner is not moving

Not connected to electricity.

The outlet the control unit is connected to, is not supplying 

electrical power. Check that the outlet to which the control 

unit is connected is receiving electricity.

Cycle not started.

Press the Start button to initiate a cleaning cycle. 

Reset needed.

Disconnect the unit power and reconnect after 20 seconds. 

If the problem is not resolved, contact your local retailer to 

request a diagnostic review or contact AstralPool Consumer 

Care 1300 186 875.

The floating cable has 

excessive tangling

Too much cable in the water.

Place only the required amount of cable into the water 

to allow it to reach the farthest end of your pool with 

remaining cable on the pool deck. (See: 

Install and Submerge 

the Cleaner

).

Removal needed.

Untangle the twisted cord and lay in sun to reduce memory. 

(See: 

Cord Tangling

).

The cleaner is not cleaning the 

pool effectively.

Filter canister is full or dirty.

Dispose of debris and thoroughly clean the filter canister 

with mild soap and a soft brush. Then, re-submerge the 

cleaner (see: 

Clean the Filter Canister

).

Brushes are worn.

Check the wear indicator(s). Contact your local dealer for 

spare parts.

Cable is excessively tangled.

Untangle the twisted cord and lay in sun to reduce memory. 

(See: 

Cord Tangling

).

Section 7.  Conformity  

IEC 60335-2-41

Australian Cert. No. SAA100894EA

 

                         SAA100540

3145455L100001-01A

87002641965

 

The manufacturer reserves the right to modify these specifications without notice. Although the cleaning robots 

have been tested in a large variety of swimming pools, AstralPool cannot be held responsible in the case of a non-

perfect adaptation of the robot to a particular swimming pool.

Summary of Contents for QB800

















Reviews: