background image

3

QB800 robotic cleaner   

Owner’s Manual

2

QB800 robotic cleaner   

Owner’s Manual

Table of Contents

Section 1.  Important Safety Instructions ..... 4

Section 2.  Cleaner Specifications ................. 5

Section 3.  Assembly ....................................... 6

3.1 Contents ......................................................................................6
3.2  Assemble the Transport Caddy ...........................................6
3.3  Attach the Control Unit to the Caddy ...............................7
3.4  Connect to a Power Source ..................................................8

Section 4.  General Cleaner Operation .......... 9

4.1  Install and Submerge the Cleaner ......................................9
4.2  Cleaner Control Unit ............................................................ 10
4.3  Start / Stop Cleaning ............................................................ 11
4.4  Elevate System ....................................................................... 11

Section 5.   Storage & Maintenance ............. 11

5.1  Cord Tangling ......................................................................... 11
5.2  Clean the Filter Canister ...................................................... 12
5.3  Store the Cleaner When Not in Use ................................ 13
5.4  Replacing Wear Parts ........................................................... 14

Section 6.  Troubleshooting ......................... 16

6.1  Control Unit Status Indicator Lights  .............................. 16
6.2  General Troubleshooting .................................................... 17

Section 7.  Conformity  ................................. 18

Summary of Contents for QB800

















Reviews: