background image

 
11 

firmware version 1.X.X

 

Nexus-II User Manual 

FCC Statement for Nexus-II

 

 
 
 
 
 
 
This  device  complies  with  Part  15  of  the  FCC  Rules.  Operation  is 
subject to the following two conditions: (1) this device may not cause 
harmful  interference,  and  (2)  this  device  must  accept  any 
interference  received,  including  interference  that  may  cause 
undesired operation.  
 

NOTE:

 To comply with FCC RF exposure compliance requirements, 

the antenna used for this transmitter must be installed to provide a 
separation distance of at least 20 cm from all persons and must not 
be co-located or operating in conjunction with any other antenna or 
transmitter.  
 

NOTE: 

This  equipment  has  been  tested  and  found  to  comply  with 

the limits for a Class B digital device, pursuant to Part 15 of the FCC 
Rules.  These  limits  are  designed  to  provide  reasonable  protection 
against  harmful  interference  in  a  residential  installation.  This 
equipment generates, uses and can radiate radio frequency energy 
and,  if  not  installed  and  used  in  accordance  with  the  instructions, 
may cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular 
installation.  If  this  equipment  does  cause  harmful  interference  to 
radio or television reception, which can be determined by turning the 
equipment  off  and  on,  the  user  is  encouraged  to  try  to  correct  the 
interference by one or more of the following measures: 

 

 

Reorient or relocate the receiving antenna 

 

 

Increase the separation between the equipment and receiver 

 

 
 

 

 

Contains: 

FCC ID: 2AC7Z-ESPWROOM02 

 

Summary of Contents for Nexus-II





















Reviews: